Configuration files updated to Marlin 2.1.2 and Bugfix 2.1.x

Preparing for Input Shaping Support

Configurator.pyw

@@ -50,7 +50,7 @@ def auto_name():
     if "F1-UBL" not in Name and "F4-UBL" not in Name:
       Name = Name.replace("-UBL","UBL")
     #rename LinaAdv
-    Name = Name.replace("LinAdv","LA")
+    #Name = Name.replace("LinAdv","LA")
     root.ConfigName.delete(-1,END)
     root.ConfigName.insert(-1,Name)
     root.update_conf()

Ender2Pro-ManualMesh/Configuration.h

@@ -500,7 +500,7 @@
  *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
  *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
  *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
- *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    66 : 4.7MΩ  Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
  *    67 : 500kΩ  SliceEngineering 450°C Thermistor
  *    68 : PT100 amplifier board from Dyze Design
  *    70 : 100kΩ  bq Hephestos 2
@@ -522,6 +522,7 @@
  *   110 : Pt100  with 1kΩ pullup (atypical)
  *   147 : Pt100  with 4.7kΩ pullup
  *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1022 : Pt1000 with 2.2kΩ pullup
  *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
  *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
  *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
@@ -567,6 +568,10 @@
   #define MAX31865_SENSOR_OHMS_1      100
   #define MAX31865_CALIBRATION_OHMS_1 430
 #endif
+#if TEMP_SENSOR_IS_MAX_TC(2)
+  #define MAX31865_SENSOR_OHMS_2      100
+  #define MAX31865_CALIBRATION_OHMS_2 430
+#endif
 
 #if HAS_E_TEMP_SENSOR
   #define TEMP_RESIDENCY_TIME         10  // (seconds) Time to wait for hotend to "settle" in M109
@@ -878,7 +883,7 @@
 //#define POLARGRAPH
 #if ENABLED(POLARGRAPH)
   #define POLARGRAPH_MAX_BELT_LEN 1035.0
-  #define POLAR_SEGMENTS_PER_SECOND 5
+  #define DEFAULT_SEGMENTS_PER_SECOND 5
 #endif
 
 // @section delta
@@ -890,28 +895,26 @@
   // Make delta curves from many straight lines (linear interpolation).
   // This is a trade-off between visible corners (not enough segments)
   // and processor overload (too many expensive sqrt calls).
-  #define DELTA_SEGMENTS_PER_SECOND 200
+  #define DEFAULT_SEGMENTS_PER_SECOND 200
 
   // After homing move down to a height where XY movement is unconstrained
   //#define DELTA_HOME_TO_SAFE_ZONE
 
   // Delta calibration menu
-  // uncomment to add three points calibration menu option.
+  // Add three-point calibration to the MarlinUI menu.
   // See http://minow.blogspot.com/index.html#4918805519571907051
   //#define DELTA_CALIBRATION_MENU
 
-  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  // G33 Delta Auto-Calibration. Enable EEPROM_SETTINGS to store results.
   //#define DELTA_AUTO_CALIBRATION
 
-  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
-
   #if ENABLED(DELTA_AUTO_CALIBRATION)
-    // set the default number of probe points : n*n (1 -> 7)
+    // Default number of probe points : n*n (1 -> 7)
     #define DELTA_CALIBRATION_DEFAULT_POINTS 4
   #endif
 
   #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
-    // Set the steprate for papertest probing
+    // Step size for paper-test probing
     #define PROBE_MANUALLY_STEP 0.05      // (mm)
   #endif
 
@@ -956,7 +959,7 @@
 //#define MP_SCARA
 #if EITHER(MORGAN_SCARA, MP_SCARA)
   // If movement is choppy try lowering this value
-  #define SCARA_SEGMENTS_PER_SECOND 200
+  #define DEFAULT_SEGMENTS_PER_SECOND 200
 
   // Length of inner and outer support arms. Measure arm lengths precisely.
   #define SCARA_LINKAGE_1 150       // (mm)
@@ -992,18 +995,18 @@
 // Enable for TPARA kinematics and configure below
 //#define AXEL_TPARA
 #if ENABLED(AXEL_TPARA)
-  #define DEBUG_ROBOT_KINEMATICS
-  #define ROBOT_SEGMENTS_PER_SECOND 200
+  #define DEBUG_TPARA_KINEMATICS
+  #define DEFAULT_SEGMENTS_PER_SECOND 200
 
   // Length of inner and outer support arms. Measure arm lengths precisely.
-  #define ROBOT_LINKAGE_1 120       // (mm)
-  #define ROBOT_LINKAGE_2 120       // (mm)
+  #define TPARA_LINKAGE_1 120       // (mm)
+  #define TPARA_LINKAGE_2 120       // (mm)
 
   // SCARA tower offset (position of Tower relative to bed zero position)
   // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
-  #define ROBOT_OFFSET_X    0       // (mm)
-  #define ROBOT_OFFSET_Y    0       // (mm)
-  #define ROBOT_OFFSET_Z    0       // (mm)
+  #define TPARA_OFFSET_X    0       // (mm)
+  #define TPARA_OFFSET_Y    0       // (mm)
+  #define TPARA_OFFSET_Z    0       // (mm)
 
   #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
 
@@ -1917,17 +1920,21 @@
 #endif
 
 #if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_UBL)
-  // Gradually reduce leveling correction until a set height is reached,
-  // at which point movement will be level to the machine's XY plane.
-  // The height can be set with M420 Z<height>
+  /**
+   * Gradually reduce leveling correction until a set height is reached,
+   * at which point movement will be level to the machine's XY plane.
+   * The height can be set with M420 Z<height>
+   */
   #define ENABLE_LEVELING_FADE_HEIGHT
   #if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
     #define DEFAULT_LEVELING_FADE_HEIGHT 10.0 // (mm) Default fade height.
   #endif
 
-  // For Cartesian machines, instead of dividing moves on mesh boundaries,
-  // split up moves into short segments like a Delta. This follows the
-  // contours of the bed more closely than edge-to-edge straight moves.
+  /**
+   * For Cartesian machines, instead of dividing moves on mesh boundaries,
+   * split up moves into short segments like a Delta. This follows the
+   * contours of the bed more closely than edge-to-edge straight moves.
+   */
   #define SEGMENT_LEVELED_MOVES
   #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one)
 
@@ -2748,7 +2755,7 @@
 
 //
 // ReprapWorld Graphical LCD
-// https://reprapworld.com/?products_details&products_id/1218
+// https://reprapworld.com/electronics/3d-printer-modules/autonomous-printing/graphical-lcd-screen-v1-0/
 //
 //#define REPRAPWORLD_GRAPHICAL_LCD
 
@@ -3003,6 +3010,7 @@
 //#define ANYCUBIC_LCD_CHIRON
 #if EITHER(ANYCUBIC_LCD_I3MEGA, ANYCUBIC_LCD_CHIRON)
   //#define ANYCUBIC_LCD_DEBUG
+  //#define ANYCUBIC_LCD_GCODE_EXT  // Add ".gcode" to menu entries for DGUS clone compatibility
 #endif
 
 //
@@ -3071,7 +3079,7 @@
 //#define MKS_ROBIN_TFT_V1_1R
 
 //
-// 480x320, 3.5", FSMC Stock Display from TronxXY
+// 480x320, 3.5", FSMC Stock Display from Tronxy
 //
 //#define TFT_TRONXY_X5SA
 
@@ -3138,6 +3146,10 @@
 //#define TFT_COLOR_UI
 //#define TFT_LVGL_UI
 
+#if ENABLED(TFT_COLOR_UI)
+  //#define TFT_SHARED_SPI   // SPI is shared between TFT display and other devices. Disable async data transfer
+#endif
+
 #if ENABLED(TFT_LVGL_UI)
   //#define MKS_WIFI_MODULE  // MKS WiFi module
 #endif
@@ -3278,16 +3290,19 @@
  * luminance values can be set from 0 to 255.
  * For NeoPixel LED an overall brightness parameter is also available.
  *
- * *** CAUTION ***
+ *  === CAUTION ===
  *  LED Strips require a MOSFET Chip between PWM lines and LEDs,
  *  as the Arduino cannot handle the current the LEDs will require.
  *  Failure to follow this precaution can destroy your Arduino!
+ *
  *  NOTE: A separate 5V power supply is required! The NeoPixel LED needs
  *  more current than the Arduino 5V linear regulator can produce.
- * *** CAUTION ***
  *
- * LED Type. Enable only one of the following two options.
+ *  Requires PWM frequency between 50 <> 100Hz (Check HAL or variant)
+ *  Use FAST_PWM_FAN, if possible, to reduce fan noise.
  */
+
+// LED Type. Enable only one of the following two options:
 //#define RGB_LED
 //#define RGBW_LED
 
@@ -3296,6 +3311,10 @@
   //#define RGB_LED_G_PIN 43
   //#define RGB_LED_B_PIN 35
   //#define RGB_LED_W_PIN -1
+  //#define RGB_STARTUP_TEST              // For PWM pins, fade between all colors
+  #if ENABLED(RGB_STARTUP_TEST)
+    #define RGB_STARTUP_TEST_INNER_MS 10  // (ms) Reduce or increase fading speed
+  #endif
 #endif
 
 // Support for Adafruit NeoPixel LED driver
@@ -3317,6 +3336,7 @@
     #define NEOPIXEL2_PIXELS           15 // Number of LEDs in the second strip
     #define NEOPIXEL2_BRIGHTNESS      127 // Initial brightness (0-255)
     #define NEOPIXEL2_STARTUP_TEST        // Cycle through colors at startup
+    #define NEOPIXEL_M150_DEFAULT      -1 // Default strip for M150 without 'S'. Use -1 to set all by default.
   #else
     //#define NEOPIXEL2_INSERIES          // Default behavior is NeoPixel 2 in parallel
   #endif