Update configuration files

Ender2Pro-ManualMesh/Configuration.h

@@ -2218,16 +2218,21 @@
 #define PREHEAT_1_FAN_SPEED     128 // Value from 0 to 255
 
 #define PREHEAT_2_LABEL       "ABS"
-#define PREHEAT_2_TEMP_HOTEND 230
-#define PREHEAT_2_TEMP_BED     80
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED     90
 #define PREHEAT_2_TEMP_CHAMBER 35
 #define PREHEAT_2_FAN_SPEED     128 // Value from 0 to 255
 
-#define PREHEAT_3_LABEL       "CUSTOM"
-#define PREHEAT_3_TEMP_HOTEND 240
-#define PREHEAT_3_TEMP_BED     60
+#define PREHEAT_3_LABEL       "PETG"
+#define PREHEAT_3_TEMP_HOTEND 230
+#define PREHEAT_3_TEMP_BED     80
 #define PREHEAT_3_FAN_SPEED   128
 
+#define PREHEAT_4_LABEL       "CUSTOM"
+#define PREHEAT_4_TEMP_HOTEND 190
+#define PREHEAT_4_TEMP_BED     50
+#define PREHEAT_4_FAN_SPEED   128
+
 // @section motion
 
 /**

Ender3S1-F1-EZABLZN/Configuration.h

@@ -1588,7 +1588,7 @@
  * These options are most useful for the BLTouch probe, but may also improve
  * readings with inductive probes and piezo sensors.
  */
-#define PROBING_HEATERS_OFF       // Turn heaters off when probing  // MRiscoC Enabled for EZABL version
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
 #if ENABLED(PROBING_HEATERS_OFF)
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
   //#define WAIT_FOR_HOTEND         // Wait for hotend to heat back up between probes (to improve accuracy & prevent cold extrude)
@@ -2218,16 +2218,21 @@
 #define PREHEAT_1_FAN_SPEED     128 // Value from 0 to 255
 
 #define PREHEAT_2_LABEL       "ABS"
-#define PREHEAT_2_TEMP_HOTEND 230
-#define PREHEAT_2_TEMP_BED     80
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED     90
 #define PREHEAT_2_TEMP_CHAMBER 35
 #define PREHEAT_2_FAN_SPEED     128 // Value from 0 to 255
 
-#define PREHEAT_3_LABEL       "CUSTOM"
-#define PREHEAT_3_TEMP_HOTEND 240
-#define PREHEAT_3_TEMP_BED     60
+#define PREHEAT_3_LABEL       "PETG"
+#define PREHEAT_3_TEMP_HOTEND 230
+#define PREHEAT_3_TEMP_BED     80
 #define PREHEAT_3_FAN_SPEED   128
 
+#define PREHEAT_4_LABEL       "CUSTOM"
+#define PREHEAT_4_TEMP_HOTEND 190
+#define PREHEAT_4_TEMP_BED     50
+#define PREHEAT_4_FAN_SPEED   128
+
 // @section motion
 
 /**

Ender3S1-F1-MM/Configuration.h

@@ -2218,16 +2218,21 @@
 #define PREHEAT_1_FAN_SPEED     128 // Value from 0 to 255
 
 #define PREHEAT_2_LABEL       "ABS"
-#define PREHEAT_2_TEMP_HOTEND 230
-#define PREHEAT_2_TEMP_BED     80
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED     90
 #define PREHEAT_2_TEMP_CHAMBER 35
 #define PREHEAT_2_FAN_SPEED     128 // Value from 0 to 255
 
-#define PREHEAT_3_LABEL       "CUSTOM"
-#define PREHEAT_3_TEMP_HOTEND 240
-#define PREHEAT_3_TEMP_BED     60
+#define PREHEAT_3_LABEL       "PETG"
+#define PREHEAT_3_TEMP_HOTEND 230
+#define PREHEAT_3_TEMP_BED     80
 #define PREHEAT_3_FAN_SPEED   128
 
+#define PREHEAT_4_LABEL       "CUSTOM"
+#define PREHEAT_4_TEMP_HOTEND 190
+#define PREHEAT_4_TEMP_BED     50
+#define PREHEAT_4_FAN_SPEED   128
+
 // @section motion
 
 /**

Ender3S1-F1-UBL-LA/Configuration.h

@@ -1588,7 +1588,7 @@
  * These options are most useful for the BLTouch probe, but may also improve
  * readings with inductive probes and piezo sensors.
  */
-#define PROBING_HEATERS_OFF       // Turn heaters off when probing  // MRiscoC Probe stability
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
 #if ENABLED(PROBING_HEATERS_OFF)
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
   //#define WAIT_FOR_HOTEND         // Wait for hotend to heat back up between probes (to improve accuracy & prevent cold extrude)
@@ -2218,16 +2218,21 @@
 #define PREHEAT_1_FAN_SPEED     128 // Value from 0 to 255
 
 #define PREHEAT_2_LABEL       "ABS"
-#define PREHEAT_2_TEMP_HOTEND 230
-#define PREHEAT_2_TEMP_BED     80
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED     90
 #define PREHEAT_2_TEMP_CHAMBER 35
 #define PREHEAT_2_FAN_SPEED     128 // Value from 0 to 255
 
-#define PREHEAT_3_LABEL       "CUSTOM"
-#define PREHEAT_3_TEMP_HOTEND 240
-#define PREHEAT_3_TEMP_BED     60
+#define PREHEAT_3_LABEL       "PETG"
+#define PREHEAT_3_TEMP_HOTEND 230
+#define PREHEAT_3_TEMP_BED     80
 #define PREHEAT_3_FAN_SPEED   128
 
+#define PREHEAT_4_LABEL       "CUSTOM"
+#define PREHEAT_4_TEMP_HOTEND 190
+#define PREHEAT_4_TEMP_BED     50
+#define PREHEAT_4_FAN_SPEED   128
+
 // @section motion
 
 /**

Ender3S1-F1-UBL-MPC/Configuration.h

@@ -1588,7 +1588,7 @@
  * These options are most useful for the BLTouch probe, but may also improve
  * readings with inductive probes and piezo sensors.
  */
-#define PROBING_HEATERS_OFF       // Turn heaters off when probing  // MRiscoC Probe stability
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
 #if ENABLED(PROBING_HEATERS_OFF)
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
   //#define WAIT_FOR_HOTEND         // Wait for hotend to heat back up between probes (to improve accuracy & prevent cold extrude)
@@ -2218,16 +2218,21 @@
 #define PREHEAT_1_FAN_SPEED     128 // Value from 0 to 255
 
 #define PREHEAT_2_LABEL       "ABS"
-#define PREHEAT_2_TEMP_HOTEND 230
-#define PREHEAT_2_TEMP_BED     80
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED     90
 #define PREHEAT_2_TEMP_CHAMBER 35
 #define PREHEAT_2_FAN_SPEED     128 // Value from 0 to 255
 
-#define PREHEAT_3_LABEL       "CUSTOM"
-#define PREHEAT_3_TEMP_HOTEND 240
-#define PREHEAT_3_TEMP_BED     60
+#define PREHEAT_3_LABEL       "PETG"
+#define PREHEAT_3_TEMP_HOTEND 230
+#define PREHEAT_3_TEMP_BED     80
 #define PREHEAT_3_FAN_SPEED   128
 
+#define PREHEAT_4_LABEL       "CUSTOM"
+#define PREHEAT_4_TEMP_HOTEND 190
+#define PREHEAT_4_TEMP_BED     50
+#define PREHEAT_4_FAN_SPEED   128
+
 // @section motion
 
 /**

Ender3S1-F1-UBL-T13/Configuration.h

@@ -1588,7 +1588,7 @@
  * These options are most useful for the BLTouch probe, but may also improve
  * readings with inductive probes and piezo sensors.
  */
-#define PROBING_HEATERS_OFF       // Turn heaters off when probing  // MRiscoC Probe stability
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
 #if ENABLED(PROBING_HEATERS_OFF)
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
   //#define WAIT_FOR_HOTEND         // Wait for hotend to heat back up between probes (to improve accuracy & prevent cold extrude)
@@ -2218,16 +2218,21 @@
 #define PREHEAT_1_FAN_SPEED     128 // Value from 0 to 255
 
 #define PREHEAT_2_LABEL       "ABS"
-#define PREHEAT_2_TEMP_HOTEND 230
-#define PREHEAT_2_TEMP_BED     80
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED     90
 #define PREHEAT_2_TEMP_CHAMBER 35
 #define PREHEAT_2_FAN_SPEED     128 // Value from 0 to 255
 
-#define PREHEAT_3_LABEL       "CUSTOM"
-#define PREHEAT_3_TEMP_HOTEND 240
-#define PREHEAT_3_TEMP_BED     60
+#define PREHEAT_3_LABEL       "PETG"
+#define PREHEAT_3_TEMP_HOTEND 230
+#define PREHEAT_3_TEMP_BED     80
 #define PREHEAT_3_FAN_SPEED   128
 
+#define PREHEAT_4_LABEL       "CUSTOM"
+#define PREHEAT_4_TEMP_HOTEND 190
+#define PREHEAT_4_TEMP_BED     50
+#define PREHEAT_4_FAN_SPEED   128
+
 // @section motion
 
 /**

Ender3S1-F1-UBL/Configuration.h

@@ -1588,7 +1588,7 @@
  * These options are most useful for the BLTouch probe, but may also improve
  * readings with inductive probes and piezo sensors.
  */
-#define PROBING_HEATERS_OFF       // Turn heaters off when probing  // MRiscoC Probe stability
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
 #if ENABLED(PROBING_HEATERS_OFF)
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
   //#define WAIT_FOR_HOTEND         // Wait for hotend to heat back up between probes (to improve accuracy & prevent cold extrude)
@@ -2218,16 +2218,21 @@
 #define PREHEAT_1_FAN_SPEED     128 // Value from 0 to 255
 
 #define PREHEAT_2_LABEL       "ABS"
-#define PREHEAT_2_TEMP_HOTEND 230
-#define PREHEAT_2_TEMP_BED     80
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED     90
 #define PREHEAT_2_TEMP_CHAMBER 35
 #define PREHEAT_2_FAN_SPEED     128 // Value from 0 to 255
 
-#define PREHEAT_3_LABEL       "CUSTOM"
-#define PREHEAT_3_TEMP_HOTEND 240
-#define PREHEAT_3_TEMP_BED     60
+#define PREHEAT_3_LABEL       "PETG"
+#define PREHEAT_3_TEMP_HOTEND 230
+#define PREHEAT_3_TEMP_BED     80
 #define PREHEAT_3_FAN_SPEED   128
 
+#define PREHEAT_4_LABEL       "CUSTOM"
+#define PREHEAT_4_TEMP_HOTEND 190
+#define PREHEAT_4_TEMP_BED     50
+#define PREHEAT_4_FAN_SPEED   128
+
 // @section motion
 
 /**

Ender3S1-F1/Configuration.h

@@ -1588,7 +1588,7 @@
  * These options are most useful for the BLTouch probe, but may also improve
  * readings with inductive probes and piezo sensors.
  */
-#define PROBING_HEATERS_OFF       // Turn heaters off when probing  // MRiscoC Probe stability
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
 #if ENABLED(PROBING_HEATERS_OFF)
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
   //#define WAIT_FOR_HOTEND         // Wait for hotend to heat back up between probes (to improve accuracy & prevent cold extrude)
@@ -2218,16 +2218,21 @@
 #define PREHEAT_1_FAN_SPEED     128 // Value from 0 to 255
 
 #define PREHEAT_2_LABEL       "ABS"
-#define PREHEAT_2_TEMP_HOTEND 230
-#define PREHEAT_2_TEMP_BED     80
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED     90
 #define PREHEAT_2_TEMP_CHAMBER 35
 #define PREHEAT_2_FAN_SPEED     128 // Value from 0 to 255
 
-#define PREHEAT_3_LABEL       "CUSTOM"
-#define PREHEAT_3_TEMP_HOTEND 240
-#define PREHEAT_3_TEMP_BED     60
+#define PREHEAT_3_LABEL       "PETG"
+#define PREHEAT_3_TEMP_HOTEND 230
+#define PREHEAT_3_TEMP_BED     80
 #define PREHEAT_3_FAN_SPEED   128
 
+#define PREHEAT_4_LABEL       "CUSTOM"
+#define PREHEAT_4_TEMP_HOTEND 190
+#define PREHEAT_4_TEMP_BED     50
+#define PREHEAT_4_FAN_SPEED   128
+
 // @section motion
 
 /**

Ender3S1-F4-LA/Configuration.h

@@ -1588,7 +1588,7 @@
  * These options are most useful for the BLTouch probe, but may also improve
  * readings with inductive probes and piezo sensors.
  */
-#define PROBING_HEATERS_OFF       // Turn heaters off when probing  // MRiscoC Probe stability
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
 #if ENABLED(PROBING_HEATERS_OFF)
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
   //#define WAIT_FOR_HOTEND         // Wait for hotend to heat back up between probes (to improve accuracy & prevent cold extrude)
@@ -2218,16 +2218,21 @@
 #define PREHEAT_1_FAN_SPEED     128 // Value from 0 to 255
 
 #define PREHEAT_2_LABEL       "ABS"
-#define PREHEAT_2_TEMP_HOTEND 230
-#define PREHEAT_2_TEMP_BED     80
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED     90
 #define PREHEAT_2_TEMP_CHAMBER 35
 #define PREHEAT_2_FAN_SPEED     128 // Value from 0 to 255
 
-#define PREHEAT_3_LABEL       "CUSTOM"
-#define PREHEAT_3_TEMP_HOTEND 240
-#define PREHEAT_3_TEMP_BED     60
+#define PREHEAT_3_LABEL       "PETG"
+#define PREHEAT_3_TEMP_HOTEND 230
+#define PREHEAT_3_TEMP_BED     80
 #define PREHEAT_3_FAN_SPEED   128
 
+#define PREHEAT_4_LABEL       "CUSTOM"
+#define PREHEAT_4_TEMP_HOTEND 190
+#define PREHEAT_4_TEMP_BED     50
+#define PREHEAT_4_FAN_SPEED   128
+
 // @section motion
 
 /**
@@ -2544,7 +2549,7 @@
 // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
 //
 //#define INDIVIDUAL_AXIS_HOMING_MENU
-#define INDIVIDUAL_AXIS_HOMING_SUBMENU
+//#define INDIVIDUAL_AXIS_HOMING_SUBMENU
 
 //
 // SPEAKER/BUZZER

Ender3S1-F4-LA/Configuration_adv.h

@@ -1382,7 +1382,7 @@
 #endif // HAS_MARLINUI_MENU
 
 #if ANY(HAS_DISPLAY, DWIN_LCD_PROUI, DWIN_CREALITY_LCD_JYERSUI)
-  #define SOUND_MENU_ITEM   // Add a mute option to the LCD menu  // MRiscoC Enable Sound Menu Item
+  //#define SOUND_MENU_ITEM   // Add a mute option to the LCD menu  // MRiscoC Enable Sound Menu Item
   #define SOUND_ON_DEFAULT    // Buzzer/speaker default enabled state
 #endif
 

Ender3S1-F4-MM/Configuration.h

@@ -2218,16 +2218,21 @@
 #define PREHEAT_1_FAN_SPEED     128 // Value from 0 to 255
 
 #define PREHEAT_2_LABEL       "ABS"
-#define PREHEAT_2_TEMP_HOTEND 230
-#define PREHEAT_2_TEMP_BED     80
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED     90
 #define PREHEAT_2_TEMP_CHAMBER 35
 #define PREHEAT_2_FAN_SPEED     128 // Value from 0 to 255
 
-#define PREHEAT_3_LABEL       "CUSTOM"
-#define PREHEAT_3_TEMP_HOTEND 240
-#define PREHEAT_3_TEMP_BED     60
+#define PREHEAT_3_LABEL       "PETG"
+#define PREHEAT_3_TEMP_HOTEND 230
+#define PREHEAT_3_TEMP_BED     80
 #define PREHEAT_3_FAN_SPEED   128
 
+#define PREHEAT_4_LABEL       "CUSTOM"
+#define PREHEAT_4_TEMP_HOTEND 190
+#define PREHEAT_4_TEMP_BED     50
+#define PREHEAT_4_FAN_SPEED   128
+
 // @section motion
 
 /**

Ender3S1-F4-T13/Configuration.h

@@ -1588,7 +1588,7 @@
  * These options are most useful for the BLTouch probe, but may also improve
  * readings with inductive probes and piezo sensors.
  */
-#define PROBING_HEATERS_OFF       // Turn heaters off when probing  // MRiscoC Probe stability
+//#define PROBING_HEATERS_OFF       // Turn heaters off when probing
 #if ENABLED(PROBING_HEATERS_OFF)
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
   //#define WAIT_FOR_HOTEND         // Wait for hotend to heat back up between probes (to improve accuracy & prevent cold extrude)
@@ -2218,16 +2218,21 @@
 #define PREHEAT_1_FAN_SPEED     128 // Value from 0 to 255
 
 #define PREHEAT_2_LABEL       "ABS"
-#define PREHEAT_2_TEMP_HOTEND 230
-#define PREHEAT_2_TEMP_BED     80
+#define PREHEAT_2_TEMP_HOTEND 240
+#define PREHEAT_2_TEMP_BED     90
 #define PREHEAT_2_TEMP_CHAMBER 35
 #define PREHEAT_2_FAN_SPEED     128 // Value from 0 to 255
 
-#define PREHEAT_3_LABEL       "CUSTOM"
-#define PREHEAT_3_TEMP_HOTEND 240
-#define PREHEAT_3_TEMP_BED     60
+#define PREHEAT_3_LABEL       "PETG"
+#define PREHEAT_3_TEMP_HOTEND 230
+#define PREHEAT_3_TEMP_BED     80
 #define PREHEAT_3_FAN_SPEED   128
 
+#define PREHEAT_4_LABEL       "CUSTOM"
+#define PREHEAT_4_TEMP_HOTEND 190
+#define PREHEAT_4_TEMP_BED     50
+#define PREHEAT_4_FAN_SPEED   128
+
 // @section motion
 
 /**