added stock Pico SDK rp2040.cfg to enable flashing with picoprobe

tcl/target/rp2040.cfg

@@ -0,0 +1,110 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+
+# RP2040 is a microcontroller with dual Cortex-M0+ core.
+# https://www.raspberrypi.com/documentation/microcontrollers/rp2040.html
+
+# The device requires multidrop SWD for debug.
+transport select swd
+
+source [find target/swj-dp.tcl]
+
+if { [info exists CHIPNAME] } {
+	set _CHIPNAME $CHIPNAME
+} else {
+	set _CHIPNAME rp2040
+}
+
+if { [info exists WORKAREASIZE] } {
+	set _WORKAREASIZE $WORKAREASIZE
+} else {
+	set _WORKAREASIZE 0x10000
+}
+
+if { [info exists CPUTAPID] } {
+	set _CPUTAPID $CPUTAPID
+} else {
+	set _CPUTAPID 0x01002927
+}
+
+# Set to '1' to start rescue mode
+if { [info exists RESCUE] } {
+	set _RESCUE $RESCUE
+} else {
+	set _RESCUE 0
+}
+
+# Set to '0' or '1' for single core configuration, 'SMP' for -rtos hwthread
+# handling of both cores, anything else for isolated debugging of both cores
+if { [info exists USE_CORE] } {
+	set _USE_CORE $USE_CORE
+} else {
+	set _USE_CORE SMP
+}
+set _BOTH_CORES [expr { $_USE_CORE != 0 && $_USE_CORE != 1 }]
+
+swj_newdap $_CHIPNAME cpu -expected-id $_CPUTAPID
+
+# The rescue debug port uses the DP CTRL/STAT bit DBGPWRUPREQ to reset the
+# PSM (power on state machine) of the RP2040 with a flag set in the
+# VREG_AND_POR_CHIP_RESET register. Once the reset is released
+# (by clearing the DBGPWRUPREQ flag), the bootrom will run, see this flag,
+# and halt. Allowing the user to load some fresh code, rather than loading
+# the potentially broken code stored in flash
+if { $_RESCUE } {
+	dap create $_CHIPNAME.rescue_dap -chain-position $_CHIPNAME.cpu -dp-id $_CPUTAPID -instance-id 0xf -ignore-syspwrupack
+	init
+
+	# Clear DBGPWRUPREQ
+	$_CHIPNAME.rescue_dap dpreg 0x4 0x00000000
+
+	# Verifying CTRL/STAT is 0
+	set _CTRLSTAT [$_CHIPNAME.rescue_dap dpreg 0x4]
+	if {[expr {$_CTRLSTAT & 0xf0000000}]} {
+		echo "Rescue failed, DP CTRL/STAT readback $_CTRLSTAT"
+	} else {
+		echo "Now restart OpenOCD without RESCUE flag and load code to RP2040"
+	}
+	shutdown
+}
+
+# core 0
+if { $_USE_CORE != 1 } {
+	dap create $_CHIPNAME.dap0 -chain-position $_CHIPNAME.cpu -dp-id $_CPUTAPID -instance-id 0
+	set _TARGETNAME_0 $_CHIPNAME.core0
+	target create $_TARGETNAME_0 cortex_m -dap $_CHIPNAME.dap0 -coreid 0
+	# srst does not exist; use SYSRESETREQ to perform a soft reset
+	$_TARGETNAME_0 cortex_m reset_config sysresetreq
+}
+
+# core 1
+if { $_USE_CORE != 0 } {
+	dap create $_CHIPNAME.dap1 -chain-position $_CHIPNAME.cpu -dp-id $_CPUTAPID -instance-id 1
+	set _TARGETNAME_1 $_CHIPNAME.core1
+	target create $_TARGETNAME_1 cortex_m -dap $_CHIPNAME.dap1 -coreid 1
+	$_TARGETNAME_1 cortex_m reset_config sysresetreq
+}
+
+if {[string compare $_USE_CORE SMP] == 0} {
+	$_TARGETNAME_0 configure  -rtos hwthread
+	$_TARGETNAME_1 configure  -rtos hwthread
+	target smp $_TARGETNAME_0 $_TARGETNAME_1
+}
+
+if { $_USE_CORE == 1 } {
+	set _FLASH_TARGET $_TARGETNAME_1
+} else {
+	set _FLASH_TARGET $_TARGETNAME_0
+}
+# Backup the work area. The flash probe runs an algorithm on the target CPU.
+# The flash is probed during gdb connect if gdb_memory_map is enabled (by default).
+$_FLASH_TARGET configure -work-area-phys 0x20010000 -work-area-size $_WORKAREASIZE -work-area-backup 1
+set _FLASHNAME $_CHIPNAME.flash
+flash bank $_FLASHNAME rp2040_flash 0x10000000 0 0 0 $_FLASH_TARGET
+
+if { $_BOTH_CORES } {
+	# Alias to ensure gdb connecting to core 1 gets the correct memory map
+	flash bank $_CHIPNAME.alias virtual 0x10000000 0 0 0 $_TARGETNAME_1 $_FLASHNAME
+
+	# Select core 0
+	targets $_TARGETNAME_0
+}