PreLiquidation

Overview

This repository puts together different contracts to carry out liquidations on Morpho with specific parameters chosen by the borrower. We call these user-defined Morpho Blue transactions pre-liquidations. Borrowers can set custom pre-liquidation parameters, allowing them to specify pre-liquidation incentive factors and pre-liquidation close factors. Pre-liquidation incentive factors determine incentives given to liquidators and pre-liquidation close factors limit the proportion of the position that can be closed during a liquidation.

The PreLiquidation contract serves as the endpoint for pre-liquidations using parameters chosen by borrowers. Note that pre-liquidation must be authorized on Morpho. Liquidators may perform pre-liquidations on a position using the preLiquidate entry point on a deployed PreLiquidation contract. The PreLiquidationFactory factory contract simplifies the deployment and indexing of pre-liquidation contracts.

The set of pre-liquidation parameters is composed of

• a Morpho market (id);
• a pre-liquidation loan-to-value (preLltv);
• two pre-liquidation close factor parameters (preLCF1 and preLCF2);
• two pre-liquidation incentive factor parameters (preLIF1 and preLIF2);
• a pre-liquidation oracle (preLiquidationOracle).

Pre-liquidation close factor and incentive factor

The pre-liquidation close factor and the pre-liquidation incentive factor evolve linearly with the user's LTV:

• the pre-liquidation close factor is preLCF1 when the position LTV is equal to preLltv and preLCF2 when the LTV is equal to LLTV;
• the pre-liquidation incentive factor is preLIF1 when the position LTV equals preLltv and preLIF2 when the LTV is equal to LLTV.

These functions are illustrated in the following figure:

The two main use-cases are:

1. Using normal fixed parameters when preLIF1 = preLIF2 and preLCF1 = preLCF2.
2. Using health dependent liquidation when either preLIF1 < preLIF2 or preLCF1 < preLCF2, similar to a Quasi Dutch Auction (as in Euler liquidations).

Pre-liquidation parameters restrictions

The PreLiquidation smart-contract enforces the following properties:

• preLltv < LLTV;
• preLCF1 <= preLCF2;
• preLFC1 <= 1;
• 1 <= preLIF1 <= preLIF2 <= 1 / LLTV. Note: using preLCF2 > 1, one can select at which LTV between preLltv and LLTV the entire position can be pre-liquidated. A pre-liquidation close factor higher than 100% means that the whole position is pre-liquidatable.

onPreLiquidate callback

By calling preLiquidate with a smart contract that implements the IPreLiquidationCallback interface, the liquidator can be called back. More precisely, the onPreLiquidate function of the liquidator's smart contract will be called after the collateral withdrawal and before the debt repayment. This mechanism eliminates the need for a flashloan.

PreLiquidation Oracle

The PreLiquidationParams struct includes a preLiquidationOracle attribute, allowing pre-liquidation using any compatible oracle. This oracle should implement Morpho's IOracle interface and adhere to the behavior specified in the documentation. It's possible to use the corresponding market oracle or any other oracle including OEV solutions.

PreLiquidationAddressLib

PreLiquidation contract addresses are generated using the CREATE2 opcode, allowing for predictable address computation depending on pre-liquidation parameters. The PreLiquidationAddressLib library provides a computePreLiquidationAddress function, simplifying the computation of a PreLiquidation contract's address.

Getting started

Package installation

Install Foundry.

Run tests

Run forge test.

Audits

All audits are stored in the audits folder.

License

Files in this repository are publicly available under license GPL-2.0-or-later, see LICENSE.