Allow configuring the watchdogs in the init config

esp-hal-embassy/MIGRATING-0.3.md

@@ -13,7 +13,7 @@ You no longer have to set up clocks and pass them to `esp_hal_embassy::init`.
      prelude::*,
 -    system::SystemControl,
  };
- 
+
  #[esp_hal_embassy::main]
  async fn main(_spawner: Spawner) -> ! {
 -    let peripherals = Peripherals::take();

esp-hal/CHANGELOG.md

@@ -26,6 +26,7 @@ and this project adheres to [Semantic Versioning](https://semver.org/spec/v2.0.0
 - Implement `TryFrom<u32>` for `ledc::timer::config::Duty` (#1984)
 - Expose `RtcClock::get_xtal_freq` and `RtcClock::get_slow_freq` publically for all chips (#2183)
 - TWAI support for ESP32-H2 (#2199)
+- Added a way to configure watchdogs in `esp_hal::init` (#2180)
 
 ### Changed
 

esp-hal/MIGRATING-0.20.md

@@ -158,7 +158,7 @@ configure an input pin, and pass it to `set_edge_signal` or `set_ctrl_signal`.
 -       PcntInputConfig { pull: Pull::Up },
 -   ));
 +   ch0.set_ctrl_signal(Input::new(io.pins.gpio4, Pull::Up));
- 
+
 -   let mut pin_b = io.pins.gpio5;
 -   ch0.set_edge_signal(PcntSource::from_pin(
 -       &mut pin_b,

esp-hal/src/config.rs

@@ -0,0 +1,59 @@
+//! # Configuration
+//!
+//! ## Overview
+//! This module contains the initial configuation for the system.
+//!
+//! ## Configuration
+//! In the esp_hal::init method, we can configure different parameters for the
+//! system:
+//! - CPU clock configuration.
+//! - Watchdog configuration.
+//!
+//! ## Example
+//!
+//! ### Default initialization
+//!
+//! ```rust, no_run
+#![doc = crate::before_snippet!()]
+//! let peripherals = esp_hal::init(esp_hal::Config::default());
+//! # }
+//! ```
+//! 
+//! ### Custom initialization
+//! ```rust, no_run
+#![doc = crate::before_snippet!()]
+//! let mut config = esp_hal::Config::default();
+//! config.cpu_clock = CpuClock::max();
+//! config.watchdog.rwdt =
+//!     esp_hal::config::WatchdogStatus::Enabled(fugit::MicrosDurationU64::millis(1000 as u64));
+//! let peripherals = esp_hal::init(config);
+//! # }
+//! ```
+
+/// Watchdog status.
+#[derive(Default, PartialEq)]
+pub enum WatchdogStatus {
+    /// Enables a watchdog timer with the specified timeout.
+    Enabled(fugit::MicrosDurationU64),
+    /// Disables the watchdog timer.
+    #[default]
+    Disabled,
+}
+
+/// Watchdogs configuration.
+#[non_exhaustive]
+#[derive(Default)]
+pub struct WatchdogConfig {
+    #[cfg(not(any(esp32, esp32s2)))]
+    /// Enable the super watchdog timer, which is slightly less than one second.
+    pub swd: bool,
+    /// Configures the reset watchdog timer.
+    pub rwdt: WatchdogStatus,
+    /// Configures the timg0 watchdog timer.
+    pub timg0: WatchdogStatus,
+    #[cfg(timg1)]
+    /// Configures the timg1 watchdog timer.
+    ///
+    /// By default, the bootloader does not enables this watchdog timer.
+    pub timg1: WatchdogStatus,
+}

esp-hal/src/lib.rs

@@ -168,6 +168,9 @@ pub mod analog;
 pub mod assist_debug;
 #[cfg(any(dport, hp_sys, pcr, system))]
 pub mod clock;
+
+pub mod config;
+
 #[cfg(any(xtensa, all(riscv, systimer)))]
 pub mod delay;
 #[cfg(any(gdma, pdma))]
@@ -729,6 +732,7 @@ macro_rules! before_snippet {
 
 use crate::{
     clock::{Clocks, CpuClock},
+    config::{WatchdogConfig, WatchdogStatus},
     peripherals::Peripherals,
 };
 
@@ -738,24 +742,58 @@ use crate::{
 pub struct Config {
     /// The CPU clock configuration.
     pub cpu_clock: CpuClock,
+    /// Enable watchdog timer(s).
+    pub watchdog: WatchdogConfig,
 }
 
 /// Initialize the system.
 ///
-/// This function sets up the CPU clock and returns the peripherals and clocks.
+/// This function sets up the CPU clock and watchdog, then, returns the
+/// peripherals and clocks.
 pub fn init(config: Config) -> Peripherals {
     let mut peripherals = Peripherals::take();
 
     // RTC domain must be enabled before we try to disable
     let mut rtc = crate::rtc_cntl::Rtc::new(&mut peripherals.LPWR);
+
     #[cfg(not(any(esp32, esp32s2)))]
-    rtc.swd.disable();
-    rtc.rwdt.disable();
+    if config.watchdog.swd {
+        rtc.swd.enable();
+    } else {
+        rtc.swd.disable();
+    }
 
-    unsafe {
-        crate::timer::timg::Wdt::<self::peripherals::TIMG0>::set_wdt_enabled(false);
-        #[cfg(timg1)]
-        crate::timer::timg::Wdt::<self::peripherals::TIMG1>::set_wdt_enabled(false);
+    match config.watchdog.rwdt {
+        WatchdogStatus::Enabled(duration) => {
+            rtc.rwdt.enable();
+            rtc.rwdt.set_timeout(duration);
+        }
+        WatchdogStatus::Disabled => {
+            rtc.rwdt.disable();
+        }
+    }
+
+    match config.watchdog.timg0 {
+        WatchdogStatus::Enabled(duration) => {
+            let mut timg0_wd = crate::timer::timg::Wdt::<self::peripherals::TIMG0>::new();
+            timg0_wd.enable();
+            timg0_wd.set_timeout(duration);
+        }
+        WatchdogStatus::Disabled => {
+            crate::timer::timg::Wdt::<self::peripherals::TIMG0>::new().disable();
+        }
+    }
+
+    #[cfg(timg1)]
+    match config.watchdog.timg1 {
+        WatchdogStatus::Enabled(duration) => {
+            let mut timg1_wd = crate::timer::timg::Wdt::<self::peripherals::TIMG1>::new();
+            timg1_wd.enable();
+            timg1_wd.set_timeout(duration);
+        }
+        WatchdogStatus::Disabled => {
+            crate::timer::timg::Wdt::<self::peripherals::TIMG1>::new().disable();
+        }
     }
 
     Clocks::init(config.cpu_clock);

esp-hal/src/rtc_cntl/mod.rs

@@ -988,6 +988,11 @@ impl Swd {
         Self
     }
 
+    /// Enable the watchdog timer instance
+    pub fn enable(&mut self) {
+        self.set_enabled(true);
+    }
+
     /// Disable the watchdog timer instance
     pub fn disable(&mut self) {
         self.set_enabled(false);

esp-wifi/MIGRATING-0.9.md

@@ -15,7 +15,7 @@ You no longer have to set up clocks and pass them to `esp_wifi::initialize`.
      initialize,
      // ...
  };
- 
+
  #[entry]
  fn main() -> ! {
 -    let peripherals = Peripherals::take();
@@ -65,7 +65,7 @@ The size of the heap depends on what you are going to use esp-wifi for and if yo
 
 E.g. when using `coex` you need around 92k. If not using `coex`, going lower than 72k you will observe some failed allocations but it might still work. Going even lower will make things fail.
 
-If you see linker errors regarding undefined symbols for `esp_wifi_free_internal_heap` and `esp_wifi_allocate_from_internal_ram` you either want to opt-in to use the `esp-alloc` feature 
+If you see linker errors regarding undefined symbols for `esp_wifi_free_internal_heap` and `esp_wifi_allocate_from_internal_ram` you either want to opt-in to use the `esp-alloc` feature
 or provide your own allocator (see below)
 
 ### Using your own allocator

hil-test/Cargo.toml

@@ -55,6 +55,10 @@ harness = false
 name    = "i2c"
 harness = false
 
+[[test]]
+name    = "init"
+harness = false
+
 [[test]]
 name    = "i2s"
 harness = false

hil-test/tests/init.rs

@@ -0,0 +1,110 @@
+//! Initialization tests
+
+//% CHIPS: esp32 esp32c2 esp32c3 esp32c6 esp32h2 esp32s2 esp32s3
+
+#![no_std]
+#![no_main]
+
+use esp_hal::{
+    config::WatchdogStatus,
+    delay::Delay,
+    prelude::*,
+    rtc_cntl::Rtc,
+    timer::timg::TimerGroup,
+    Config,
+};
+use hil_test as _;
+
+#[cfg(test)]
+#[embedded_test::tests]
+mod tests {
+    use super::*;
+
+    #[test]
+    #[timeout(3)]
+    fn test_feeding_timg0_wdt() {
+        let peripherals = esp_hal::init({
+            let mut config = Config::default();
+            config.watchdog.timg0 =
+                WatchdogStatus::Enabled(fugit::MicrosDurationU64::millis(500 as u64));
+            config
+        });
+
+        let timg0 = TimerGroup::new(peripherals.TIMG0);
+        let mut wdt0 = timg0.wdt;
+        let delay = Delay::new();
+
+        for _ in 0..4 {
+            wdt0.feed();
+            delay.delay(250.millis());
+        }
+    }
+
+    #[test]
+    #[timeout(3)]
+    #[cfg(timg1)]
+    fn test_feeding_timg1_wdt() {
+        let peripherals = esp_hal::init({
+            let mut config = Config::default();
+            config.watchdog.timg1 =
+                WatchdogStatus::Enabled(fugit::MicrosDurationU64::millis(500 as u64));
+            config
+        });
+
+        let timg1 = TimerGroup::new(peripherals.TIMG1);
+        let mut wdt1 = timg1.wdt;
+        let delay = Delay::new();
+
+        for _ in 0..4 {
+            wdt1.feed();
+            delay.delay(250.millis());
+        }
+    }
+
+    #[test]
+    #[timeout(3)]
+    fn test_feeding_timg0_wdt_max_clock() {
+        let peripherals = esp_hal::init({
+            let mut config = Config::default();
+            config.cpu_clock = CpuClock::max();
+            config.watchdog.timg0 =
+                WatchdogStatus::Enabled(fugit::MicrosDurationU64::millis(500 as u64));
+            config
+        });
+
+        let timg0 = TimerGroup::new(peripherals.TIMG0);
+        let mut wdt0 = timg0.wdt;
+        let delay = Delay::new();
+
+        for _ in 0..4 {
+            wdt0.feed();
+            delay.delay(250.millis());
+        }
+    }
+
+    #[test]
+    #[timeout(4)]
+    fn test_feeding_rtc_wdt() {
+        let peripherals = esp_hal::init({
+            let mut config = Config::default();
+            config.watchdog.rwdt =
+                WatchdogStatus::Enabled(fugit::MicrosDurationU64::millis(3000 as u64));
+            config
+        });
+
+        let mut rtc = Rtc::new(peripherals.LPWR);
+        let delay = Delay::new();
+
+        rtc.rwdt.feed();
+        delay.delay(2500.millis());
+    }
+
+    #[test]
+    #[timeout(3)]
+    fn test_default_config() {
+        esp_hal::init(Config::default());
+
+        let delay = Delay::new();
+        delay.delay(2000.millis());
+    }
+}