BL-Touch, Temp-Sensor,

firmware/V1.2/Marlin-2.0.7.2-SKR-mini-E3-V1.2/Marlin/Configuration.h

@@ -72,7 +72,7 @@
 // @section info
 
 // Author info of this build printed to the host during boot and M115
-#define STRING_CONFIG_H_AUTHOR "(BIGTREETECH, Ender-3)" // Who made the changes.
+#define STRING_CONFIG_H_AUTHOR "(Turol, Ender-3, modified)" // Who made the changes.
 //#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
 
 /**
@@ -133,7 +133,7 @@
 #endif
 
 // Name displayed in the LCD "Ready" message and Info menu
-#define CUSTOM_MACHINE_NAME "Ender-3"
+#define CUSTOM_MACHINE_NAME "Turol Ender-3"
 
 // Printer's unique ID, used by some programs to differentiate between machines.
 // Choose your own or use a service like https://www.uuidgenerator.net/version4
@@ -417,7 +417,7 @@
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  */
-#define TEMP_SENSOR_0 1
+#define TEMP_SENSOR_0 66
 #define TEMP_SENSOR_1 0
 #define TEMP_SENSOR_2 0
 #define TEMP_SENSOR_3 0
@@ -438,11 +438,11 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-#define TEMP_RESIDENCY_TIME     10  // (seconds) Time to wait for hotend to "settle" in M109
+#define TEMP_RESIDENCY_TIME     20  // (seconds) Time to wait for hotend to "settle" in M109
 #define TEMP_WINDOW              1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_HYSTERESIS          3  // (°C) Temperature proximity considered "close enough" to the target
 
-#define TEMP_BED_RESIDENCY_TIME 10  // (seconds) Time to wait for bed to "settle" in M190
+#define TEMP_BED_RESIDENCY_TIME 20  // (seconds) Time to wait for bed to "settle" in M190
 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
@@ -461,7 +461,7 @@
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 // (Use MINTEMP for thermistor short/failure protection.)
-#define HEATER_0_MAXTEMP 275
+#define HEATER_0_MAXTEMP 500
 #define HEATER_1_MAXTEMP 275
 #define HEATER_2_MAXTEMP 275
 #define HEATER_3_MAXTEMP 275
@@ -483,8 +483,8 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
+  #define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -632,7 +632,7 @@
   //#define ENDSTOPPULLUP_XMIN
   //#define ENDSTOPPULLUP_YMIN
   //#define ENDSTOPPULLUP_ZMIN
-  //#define ENDSTOPPULLUP_ZMIN_PROBE
+  #define ENDSTOPPULLUP_ZMIN_PROBE
 #endif
 
 // Enable pulldown for all endstops to prevent a floating state
@@ -655,7 +655,7 @@
 #define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
 #define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
 #define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -736,7 +736,7 @@
  * Override with M92
  *                                      X, Y, Z, E0 [, E1[, E2...]]
  */
-#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 400, 93 }
+#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 400, 860 }
 
 /**
  * Default Max Feed Rate (mm/s)
@@ -771,9 +771,9 @@
  *   M204 R    Retract Acceleration
  *   M204 T    Travel Acceleration
  */
-#define DEFAULT_ACCELERATION          500    // X, Y, Z and E acceleration for printing moves
-#define DEFAULT_RETRACT_ACCELERATION  500    // E acceleration for retracts
-#define DEFAULT_TRAVEL_ACCELERATION   500    // X, Y, Z acceleration for travel (non printing) moves
+#define DEFAULT_ACCELERATION          2000   // X, Y, Z and E acceleration for printing moves
+#define DEFAULT_RETRACT_ACCELERATION  2000    // E acceleration for retracts
+#define DEFAULT_TRAVEL_ACCELERATION   2000    // X, Y, Z acceleration for travel (non printing) moves
 
 /**
  * Default Jerk limits (mm/s)
@@ -894,7 +894,7 @@
 /**
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
-//#define BLTOUCH
+#define BLTOUCH
 
 /**
  * Pressure sensor with a BLTouch-like interface
@@ -981,14 +981,14 @@
  *     |    [-]    |
  *     O-- FRONT --+
  */
-#define NOZZLE_TO_PROBE_OFFSET { -40, -10, -1.85 }
+#define NOZZLE_TO_PROBE_OFFSET { 53.5, 10.35, -0.60 }
 
 // Most probes should stay away from the edges of the bed, but
 // with NOZZLE_AS_PROBE this can be negative for a wider probing area.
 #define PROBING_MARGIN 10
 
 // X and Y axis travel speed (mm/min) between probes
-#define XY_PROBE_SPEED (133*60)
+#define XY_PROBE_SPEED (166*60)
 
 // Feedrate (mm/min) for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
@@ -1030,8 +1030,8 @@
 #define Z_PROBE_LOW_POINT          -2 // Farthest distance below the trigger-point to go before stopping
 
 // For M851 give a range for adjusting the Z probe offset
-#define Z_PROBE_OFFSET_RANGE_MIN -20
-#define Z_PROBE_OFFSET_RANGE_MAX 20
+#define Z_PROBE_OFFSET_RANGE_MIN -50
+#define Z_PROBE_OFFSET_RANGE_MAX 50
 
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
@@ -1082,7 +1082,7 @@
 
 // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
 #define INVERT_X_DIR true
-#define INVERT_Y_DIR true
+#define INVERT_Y_DIR false
 #define INVERT_Z_DIR false
 
 // @section extruder
@@ -1117,13 +1117,13 @@
 // @section machine
 
 // The size of the print bed
-#define X_BED_SIZE 235
-#define Y_BED_SIZE 235
+#define X_BED_SIZE 220
+#define Y_BED_SIZE 220
 
 // Travel limits (mm) after homing, corresponding to endstop positions.
 #define X_MIN_POS 0
-#define Y_MIN_POS 0
-#define Z_MIN_POS 0
+#define Y_MIN_POS -11
+#define Z_MIN_POS -10
 #define X_MAX_POS X_BED_SIZE
 #define Y_MAX_POS Y_BED_SIZE
 #define Z_MAX_POS 250
@@ -1154,7 +1154,7 @@
 #endif
 
 #if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS)
-  //#define SOFT_ENDSTOPS_MENU_ITEM  // Enable/Disable software endstops from the LCD
+  #define SOFT_ENDSTOPS_MENU_ITEM  // Enable/Disable software endstops from the LCD
 #endif
 
 /**
@@ -1229,7 +1229,7 @@
  */
 //#define AUTO_BED_LEVELING_3POINT
 //#define AUTO_BED_LEVELING_LINEAR
-//#define AUTO_BED_LEVELING_BILINEAR
+#define AUTO_BED_LEVELING_BILINEAR
 //#define AUTO_BED_LEVELING_UBL
 //#define MESH_BED_LEVELING
 
@@ -1336,7 +1336,7 @@
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */
-//#define LCD_BED_LEVELING
+#define LCD_BED_LEVELING
 
 #if ENABLED(LCD_BED_LEVELING)
   #define MESH_EDIT_Z_STEP  0.025 // (mm) Step size while manually probing Z axis.
@@ -1345,7 +1345,7 @@
 #endif
 
 // Add a menu item to move between bed corners for manual bed adjustment
-//#define LEVEL_BED_CORNERS
+#define LEVEL_BED_CORNERS
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets
@@ -1380,15 +1380,15 @@
 // - Move the Z probe (or nozzle) to a defined XY point before Z Homing.
 // - Prevent Z homing when the Z probe is outside bed area.
 //
-//#define Z_SAFE_HOMING
+#define Z_SAFE_HOMING
 
 #if ENABLED(Z_SAFE_HOMING)
-  #define Z_SAFE_HOMING_X_POINT X_CENTER  // X point for Z homing
-  #define Z_SAFE_HOMING_Y_POINT Y_CENTER  // Y point for Z homing
+  #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2)    // X point for Z homing when homing all axes (G28).
+  #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2)    // Y point for Z homing when homing all axes (G28).
 #endif
 
 // Homing speeds (mm/min)
-#define HOMING_FEEDRATE_XY (20*60)
+#define HOMING_FEEDRATE_XY (50*60)
 #define HOMING_FEEDRATE_Z  (4*60)
 
 // Validate that endstops are triggered on homing moves
@@ -1498,14 +1498,14 @@
 
 // Preheat Constants
 #define PREHEAT_1_LABEL       "PLA"
-#define PREHEAT_1_TEMP_HOTEND 185
-#define PREHEAT_1_TEMP_BED     45
-#define PREHEAT_1_FAN_SPEED   255 // Value from 0 to 255
+#define PREHEAT_1_TEMP_HOTEND 215
+#define PREHEAT_1_TEMP_BED     60
+#define PREHEAT_1_FAN_SPEED   0 // Value from 0 to 255
 
 #define PREHEAT_2_LABEL       "ABS"
-#define PREHEAT_2_TEMP_HOTEND 240
-#define PREHEAT_2_TEMP_BED    110
-#define PREHEAT_2_FAN_SPEED   255 // Value from 0 to 255
+#define PREHEAT_2_TEMP_HOTEND 250
+#define PREHEAT_2_TEMP_BED    75
+#define PREHEAT_2_FAN_SPEED   0 // Value from 0 to 255
 
 /**
  * Nozzle Park
@@ -2349,16 +2349,16 @@
 #endif
 
 // Support for Adafruit NeoPixel LED driver
-//#define NEOPIXEL_LED
+#define NEOPIXEL_LED
 #if ENABLED(NEOPIXEL_LED)
   #define NEOPIXEL_TYPE   NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
   // #define NEOPIXEL_PIN     4       // LED driving pin
   //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE
   //#define NEOPIXEL2_PIN    5
-  #define NEOPIXEL_PIXELS 30       // Number of LEDs in the strip. (Longest strip when NEOPIXEL2_SEPARATE is disabled.)
+  #define NEOPIXEL_PIXELS 7       // Number of LEDs in the strip. (Longest strip when NEOPIXEL2_SEPARATE is disabled.)
   #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
   #define NEOPIXEL_BRIGHTNESS 127  // Initial brightness (0-255)
-  //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
+  #define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup
 
   // Support for second Adafruit NeoPixel LED driver controlled with M150 S1 ...
   //#define NEOPIXEL2_SEPARATE

firmware/V1.2/Marlin-2.0.7.2-SKR-mini-E3-V1.2/Marlin/Configuration_adv.h

@@ -347,14 +347,14 @@
 
 // The number of consecutive low temperature errors that can occur
 // before a min_temp_error is triggered. (Shouldn't be more than 10.)
-//#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0
+#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 5
 
 // The number of milliseconds a hotend will preheat before starting to check
 // the temperature. This value should NOT be set to the time it takes the
 // hot end to reach the target temperature, but the time it takes to reach
 // the minimum temperature your thermistor can read. The lower the better/safer.
 // This shouldn't need to be more than 30 seconds (30000)
-//#define MILLISECONDS_PREHEAT_TIME 0
+#define MILLISECONDS_PREHEAT_TIME 30000
 
 // @section extruder
 
@@ -684,15 +684,15 @@
 
   // Safety: The probe needs time to recognize the command.
   //         Minimum command delay (ms). Enable and increase if needed.
-  //#define BLTOUCH_DELAY 500
+  #define BLTOUCH_DELAY 500
 
   /**
    * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones:
    */
 
   // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful
   //          in special cases, like noisy or filtered input configurations.
-  //#define BLTOUCH_FORCE_SW_MODE
+  #define BLTOUCH_FORCE_SW_MODE
 
   /**
    * Settings for BLTouch Smart 3.0 and 3.1
@@ -1079,7 +1079,7 @@
 
   // Add Probe Z Offset calibration to the Z Probe Offsets menu
   #if HAS_BED_PROBE
-    //#define PROBE_OFFSET_WIZARD
+    #define PROBE_OFFSET_WIZARD
     #if ENABLED(PROBE_OFFSET_WIZARD)
       #define PROBE_OFFSET_START -4.0   // Estimated nozzle-to-probe Z offset, plus a little extra
     #endif
@@ -1629,9 +1629,9 @@
     #endif
   #endif
 
-  //#define BABYSTEP_DISPLAY_TOTAL          // Display total babysteps since last G28
+  #define BABYSTEP_DISPLAY_TOTAL          // Display total babysteps since last G28
 
-  //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
+  #define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets
     //#define BABYSTEP_ZPROBE_GFX_OVERLAY   // Enable graphical overlay on Z-offset editor

firmware/V1.2/Marlin-2.0.7.2-SKR-mini-E3-V1.2/platformio.ini

@@ -18,7 +18,7 @@
 [platformio]
 src_dir      = Marlin
 boards_dir   = buildroot/share/PlatformIO/boards
-default_envs = STM32F103RC_btt
+default_envs = STM32F103RC_btt_512K 
 include_dir  = Marlin
 
 #
@@ -751,7 +751,7 @@ extra_scripts     = ${common.extra_scripts}
 lib_deps          = ${common.lib_deps}
   SoftwareSerialM
   USBComposite for [email protected]
-custom_marlin.NEOPIXEL_LED = Adafruit NeoPixel=https://github.com/ccccmagicboy/Adafruit_NeoPixel#meeb_3dp_use
+custom_marlin.NEOPIXEL_LED = Adafruit NeoPixel=https://github.com/bigtreetech/Adafruit_NeoPixel#meeb_3dp_use
 debug_tool        = stlink
 upload_protocol   = dfu