Skip to content

Xinyuan-LilyGO/T-Display-S3-AMOLED-1.43

Repository files navigation

T-Display-S3-AMOLED-1.43

English | 中文

Version iteration:

Version Update date
T-Display-S3-AMOLED-1.43_V1.0 2024-04-08

PurchaseLink

Product SOC FLASH PSRAM Link
T-Display-S3-AMOLED-1.43_V1.0 ESP32S3R8 16M 8M (Octal SPI) Not yet sold

Directory

Describe

T-Display-S3-AMOLED-1.43 is a development board featuring a high-definition AMOLED display with a circular shape, based on the ESP32S3, designed for standalone battery connectivity.

Preview

PCB board

Rendering

Module

1.MCU

2. Screen

  • Size: 1.43-inch AMOLED circular screen
  • Resolution: 466x466px
  • Screen type: AMOLED
  • Driver chip: SH8601
  • Compatibility library: Arduino_GFX
  • Bus communication protocol: QSPI

3. Touch

  • Chip: FT3168
  • Bus communication protocol: IIC

4. Charging chip

  • Chip: SY6970
  • Bus communication protocol: IIC
  • Other: The output waveform of the chip will be highly unstable when powered by a 5V supply without a battery connected. To stabilize the situation, it is necessary to either connect a battery or use software to disable the battery channel. By doing so, the instability will be alleviated.

5. RTC

  • Chip: PCF8563
  • Bus communication protocol: IIC

QuickStart

Examples Support

Example Support IDE And Version Description Picture
FT3168 [Platformio IDE][espressif32-v6.5.0]
[Arduino IDE][esp32_v2.0.14]
Original Test [Platformio IDE][espressif32-v6.5.0]
[Arduino IDE][esp32_v2.0.14]
Product factory original testing
GFX [Platformio IDE][espressif32-v6.5.0]
[Arduino IDE][esp32_v2.0.14]
GFX FT3168 Image [Platformio IDE][espressif32-v6.5.0]
[Arduino IDE][esp32_v2.0.14]
SY6970 [Platformio IDE][espressif32-v6.5.0]
[Arduino IDE][esp32_v2.0.14]
SY6970 OTG [Platformio IDE][espressif32-v6.5.0]
[Arduino IDE][esp32_v2.0.14]
Light Sleep Wake Up [Platformio IDE][espressif32-v6.5.0]
[Arduino IDE][esp32_v2.0.14]
Deep Sleep Wake Up [Platformio IDE][espressif32-v6.5.0]
[Arduino IDE][esp32_v2.0.14]
PCF8563 [Platformio IDE][espressif32-v6.5.0]
[Arduino IDE][esp32_v2.0.14]
PCF8563 Scheduled INT [Platformio IDE][espressif32-v6.5.0]
[Arduino IDE][esp32_v2.0.14]
PCF8563 Timer INT [Platformio IDE][espressif32-v6.5.0]
[Arduino IDE][esp32_v2.0.14]
Deep Sleep PCF8563 Scheduled Wake Up [Platformio IDE][espressif32-v6.5.0]
[Arduino IDE][esp32_v2.0.14]
Deep Sleep PCF8563 Timer Wake Up [Platformio IDE][espressif32-v6.5.0]
[Arduino IDE][esp32_v2.0.14]
SD [Platformio IDE][espressif32-v6.5.0]
[Arduino IDE][esp32_v2.0.14]
Firmware Description Picture
Original Test V1.0.0 Original
Light Sleep V1.0.0 Original
Deep Sleep V1.0.0 Original

PlatformIO

  1. InstallVisualStudioCode,Choose installation based on your system type.

  2. Open the "Extension" section of the Visual Studio Code software sidebar(Alternatively, use "Ctrl+Shift+X" to open the extension),Search for the "PlatformIO IDE" extension and download it.

  3. During the installation of the extension, you can go to GitHub to download the program. You can download the main branch by clicking on the "<> Code" with green text, or you can download the program versions from the "Releases" section in the sidebar.

  4. After the installation of the extension is completed, open the Explorer in the sidebar(Alternatively, use "Ctrl+Shift+E" go open it),Click on "Open Folder," locate the project code you just downloaded (the entire folder), and click "Add." At this point, the project files will be added to your workspace.

  5. Open the "platformio.ini" file in the project folder (PlatformIO will automatically open the "platformio.ini" file corresponding to the added folder). Under the "[platformio]" section, uncomment and select the example program you want to burn (it should start with "default_envs = xxx") Then click "" in the bottom left corner to compile,If the compilation is correct, connect the microcontroller to the computer and click "" in the bottom left corner to download the program.

Arduino

  1. InstallArduino,Choose installation based on your system type.

  2. Open the "example" directory within the project folder, select the example project folder, and open the file ending with ".ino" to open the Arduino IDE project workspace.

  3. Open the "Tools" menu at the top right -> Select "Board" -> "Board Manager." Find or search for "esp32" and download the board files from the author named "Espressif Systems." Then, go back to the "Board" menu and select the development board type under "ESP32 Arduino." The selected development board type should match the one specified in the "platformio.ini" file under the [env] section with the header "board = xxx." If there is no corresponding development board, you may need to manually add the development board from the "board" directory within your project folder.

  4. Open menu bar "File" -> "Preferences" ,Find "Sketchbook location" here,copy and paste all library files and folders from the "libraries" folder in the project directory into the "libraries" folder in this directory.

  5. Select the correct settings in the Tools menu, as shown in the table below.

ESP32-S3

Setting Value
Board ESP32S3 Dev Module
Upload Speed 921600
USB Mode Hardware CDC and JTAG
USB CDC On Boot Enabled
USB Firmware MSC On Boot Disabled
USB DFU On Boot Disabled
CPU Frequency 240MHz (WiFi)
Flash Mode QIO 80MHz
Flash Size 16MB (128Mb)
Core Debug Level None
PSRAM OPI PSRAM
Arduino Runs On Core 1
Events Run On Core 1
  1. Select the correct port.

  2. Click "" in the upper right corner to compile,If the compilation is correct, connect the microcontroller to the computer,Click "" in the upper right corner to download.

firmware download

  1. Open the project file "tools" and locate the ESP32 burning tool. Open it.

  2. Select the correct burning chip and burning method, then click "OK." As shown in the picture, follow steps 1->2->3->4->5 to burn the program. If the burning is not successful, press and hold the "BOOT-0" button and then download and burn again.

  3. Burn the file in the root directory of the project file "firmware" file,There is a description of the firmware file version inside, just choose the appropriate version to download.

example example

PinOverview

AMOLED Screen Pin ESP32S3 Pin
SDIO0 IO11
SDIO1 IO13
SDIO2 IO14
SDIO3 IO15
SCLK IO12
CS IO10
RST IO17
EN IO16
Touch Chip Pin ESP32S3 Pin
INT IO9
SDA IO7
SCL IO6
Power Chip Pin ESP32S3 Pin
SDA IO7
SCL IO6
Battery Measurement Pin ESP32S3 Pin
BATTERY_VOLTAGE_ADC_DATA IO4
SD Card Pin ESP32S3 Pin
CS IO4
MOSI IO39
MISO IO40
SCLK IO41

RelatedTests

Power Dissipation

Firmware Program Description Picture
[T-Display-S3-AMOLED-1.43_V1.0][Light_Sleep_Wake_Up]_firmware_V1.0.0.bin Light Sleep Wake Up Power dissipation: 1282.8uA

example

[T-Display-S3-AMOLED-1.43_V1.0][Deep_Sleep_Wake_Up]_firmware_V1.0.0.bin Deep Sleep Wake Up Power dissipation: 174.2uA

example

FAQ

  • Q. After reading the above tutorials, I still don't know how to build a programming environment. What should I do?
  • A. If you still don't understand how to build an environment after reading the above tutorials, you can refer to the LilyGo-Document document instructions to build it.

  • Q. Why does Arduino IDE prompt me to update library files when I open it? Should I update them or not?
  • A. Choose not to update library files. Different versions of library files may not be mutually compatible, so it is not recommended to update library files.

  • Q. Why is there no serial data output on the "Uart" interface on my board? Is it defective and unusable?
  • A. The default project configuration uses the USB interface as Uart0 serial output for debugging purposes. The "Uart" interface is connected to Uart0, so it won't output any data without configuration.
    For PlatformIO users, please open the project file "platformio.ini" and modify the option under "build_flags = xxx" from "-D ARDUINO_USB_CDC_ON_BOOT=true" to "-D ARDUINO_USB_CDC_ON_BOOT=false" to enable external "Uart" interface.
    For Arduino users, open the "Tools" menu and select "USB CDC On Boot: Disabled" to enable the external "Uart" interface.

  • Q. Why is my board continuously failing to download the program?
  • A. Please hold down the "BOOT-0" button and try downloading the program again.

Project

Information

DependentLibraries

About

No description, website, or topics provided.

Resources

License

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published