Merge pull request #34 from OpenROV/30.0.3

30.0.3

.gitignore

@@ -23,3 +23,14 @@ OpenROV/Debug/*
 OpenROV/Visual Micro/*
 
 OpenROV_tests/.build/*
+
+OpenRov/__vm/*
+dist/
+
+*.sdf
+*.sln
+*.opensdf
+*.suo
+*.vcxproj
+*.filters
+

.travis.yml

@@ -44,7 +44,7 @@ deploy:
   on:
     repo: OpenROV/openrov-software-arduino
     all_branches: true
-    condition: "($REAL_GIT_BRANCH = master )||($REAL_GIT_BRANCH = pre-release )||($REAL_GIT_BRANCH = stable)"
+    condition: "($REAL_GIT_BRANCH = 30.0.3 )"
 
 notifications:
   webhooks:

OpenROV/AConfig.h

@@ -1,45 +1,65 @@
-#ifndef __ACONFIG_H_
-#define __ACONFIG_H_
+#pragma once
 
-/* This must be before alphabetically before all other files that reference these settings for the compiler to work
-*  or you may get vtable errors.
-*/
-
-/* This section is for devices and their configuration. IF you have not setup you pins with the
+/* This section is for modules and their configuration. IF you have not setup you pins with the
 *  standard configuration of the OpenROV kits, you should probably clone the cape or controlboard
 *  and change the pin definitions there.  Things not wired to specific pins but on the I2C bus will
 *  have the address defined in this file.
 */
 
 #include "BoardConfig.h"
 
-//Kit:
-// The boards are auto configure in the on beaglebone build process in the BoardConfig.h which gets
+// Kit:
+// The boards are auto configure in the on-beaglebone build process in the BoardConfig.h which gets
 // created. If running directly in an IDE, the BoardConfig.h wont exist and the #defines below will be
 // used instead.
 
-#if !defined(HAS_STD_CAPE) && !defined(HAS_OROV_CONTROLLERBOARD_25)
+// ---------------------------------------------------------
+// Standard Modules
+// ---------------------------------------------------------
+
+// Choose a cape or controller board
 #define HAS_STD_CAPE (0)
 #define HAS_OROV_CONTROLLERBOARD_25 (1)
+
+#if !(HAS_OROV_CONTROLLERBOARD_25) && !(HAS_STD_CAPE)
+#  error "You must select either standard cape or controllerboard25 in the AConfig.h file as they have predefined pin values required by other libraries."
 #endif
 
 #define HAS_STD_LIGHTS (1)
 #define HAS_STD_CALIBRATIONLASERS (1)
-#define HAS_STD_2X1_THRUSTERS (1)
 #define HAS_STD_CAMERAMOUNT (1)
-#define HAS_STD_PILOT (1)
+#define HAS_STD_AUTOPILOT (1)
+#define HAS_EXP_AUTOPILOT (0)
+#define HAS_ALT_SERVO (1)
 #define DEADMANSWITCH_ON (1)
 
-//After Market:
+// Thrusters configurations
+#define THRUSTER_CONFIG_NONE (0)
+#define THRUSTER_CONFIG_2X1 (1)
+
+// Selected Thruster Configuration
+#define THRUSTER_CONFIGURATION THRUSTER_CONFIG_2X1
+
+
+// ---------------------------------------------------------
+// After Market Modules
+// ---------------------------------------------------------
+
+// Pololu MINIMUV
 #define HAS_POLOLU_MINIMUV (0)
+
+// MS5803_XXBA Depth Sensor
 #define HAS_MS5803_XXBA (1)
 #define MS5803_XXBA_I2C_ADDRESS 0x76
+
+// MPU9150 IMU
 #define HAS_MPU9150 (1)
-#define MPU9150_EEPROM_START 2
 #define HAS_BNO055 (1)
+#define MPU9150_EEPROM_START 2
+#define HAS_ALT_SERVO (1)
+#define ALTS_MIDPOINT 1500
+#define ALTS_MINPOINT 1000
+#define ALTS_MAXPOINT 2000
 
-#if !(HAS_OROV_CONTROLLERBOARD_25) && !(HAS_STD_CAPE)
-#  error "You must select either standard cape or controllerboard25 in the AConfig.h file as they have predefined pin values required by other libraries."
-#endif
-
-#endif
+// BNO055 IMU
+#define HAS_BNO055 (1)