Serial Console Output of boot v3.0.3.56

U-Boot 2011.09 (May 10 2017 - 00:43:01)

DRAM: 64 MiB MMC: MMC: 0 SPI FLASH: 16 MB In: serial Out: serial Err: serial GPIO[2] is high Hit any key to stop autoboot: 0 roofsr size = 0x6d4998 rootsr size check failed loadkernel 0x00007FFC 0x1;bootm 0x00008000

Booting kernel from Legacy Image at 00008000 ...

Image Name: Linux-2.6.35.12 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3373680 Bytes = 3.2 MiB Load Address: 00008000 Entry Point: 00008040 Verifying Checksum ... OK XIP Kernel Image ... OK OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel. Linux version 2.6.35.12 ([email protected]) (gcc version 4.5.2 (SONiX GCC-4.5.2 Release 2011-12-06) ) #10 Wed May 10 00:58:45 EDT 2017 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00057177 CPU: VIVT data cache, VIVT instruction cache Machine: SONiX SN98600 Development Platform Memory policy: ECC disabled, Data cache writeback CPU: found ITCM 16k @ ffff4000, enabled Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 init=/linuxrc mem=64M isp=10M vc=12M vo=0M mtdparts=snx-spi:768k(uboot),3072k(kernel),7168k(rootfs),4096k(rescue),1024k(etc),256k(userconfig) PID hash table entries: 256 (order: -2, 1024 bytes) Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 64MB = 64MB total Memory: 32084k/32084k available, 33452k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xffa00000 - 0xffe00000 ( 4 MB) vmalloc : 0xc4800000 - 0xe0000000 ( 440 MB) lowmem : 0xc0000000 - 0xc4000000 ( 64 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .init : 0xc0008000 - 0xc0600000 (6112 kB) .text : 0xc0600000 - 0xc09af000 (3772 kB) .data : 0xc09ca000 - 0xc09ecfc0 ( 140 kB) SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation. RCU-based detection of stalled CPUs is disabled. Verbose stalled-CPUs detection is disabled. NR_IRQS:96 Console: colour dummy device 80x30 console [ttyS0] enabled Calibrating delay loop... 200.29 BogoMIPS (lpj=500736) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 0x00a00000 bytes system memory reserved for isp device at 0x00a90000 0x00c00000 bytes system memory reserved for vc device at 0x01490000 bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Linux media interface: v0.10 Linux video capture interface: v2.00 Advanced Linux Sound Architecture Driver Version 1.0.23. cfg80211: Calling CRDA to update world regulatory domain Switching to clocksource ft_clocksource NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 62 async_tx: api initialized (async) io scheduler noop registered (default) SONIX UART driver, (c) 2013 Sonix snx_uart.0: ttyS0 at MMIO 0x98a00000 (irq = 8) is a SONiX snx_uart.1: ttyS1 at MMIO 0x98b00000 (irq = 10) is a SONiX brd: module loaded loop: module loaded 6 cmdlinepart partitions found on MTD device snx-spi Creating 6 MTD partitions on "snx-spi": 0x000000000000-0x0000000c0000 : "uboot" 0x0000000c0000-0x0000003c0000 : "kernel" 0x0000003c0000-0x000000ac0000 : "rootfs" 0x000000ac0000-0x000000ec0000 : "rescue" 0x000000ec0000-0x000000fc0000 : "etc" 0x000000fc0000-0x000001000000 : "userconfig" snx_spi_init register PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver snx_ehci snx_ehci.0: snx_ehci snx_ehci snx_ehci.0: new USB bus registered, assigned bus number 1 snx_ehci snx_ehci.0: irq 24, io mem 0x90800000 snx_ehci snx_ehci.0: USB 0.0 started, EHCI 0.96 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: snx_ehci usb usb1: Manufacturer: Linux 2.6.35.12 ehci_hcd usb usb1: SerialNumber: sonix-ehci hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic usbserial: USB Serial Driver core USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver option option: v0.7.2:USB Driver for GSM modems mice: PS/2 mouse device common for all mice i2c /dev entries driver SONIX SNX I2C adapter driver, (c) 2012 Sonix snx_i2c.0: SNX I2C0 controller at 0x98300000 (irq = 1) I2C GPIO driver INIT snx_i2c.1: SNX I2C1 controller at 0x98400000 (irq = 2) snx_hdma snx_hdma: SNX AHB DMA Controller (memcpy memset), 4 channels SNX AHB DMA driver register usbcore: registered new interface driver usbhid usbhid: USB HID core driver usbcore: registered new interface driver snd-usb-audio ALSA device list: No soundcards found. IPv4 over IPv4 tunneling driver GRE over IPv4 tunneling driver ip_tables: (C) 2000-2006 Netfilter Core Team TCP cubic registered NET: Registered protocol family 17 lib80211: common routines for IEEE802.11 drivers Warning: unable to open an initial console. Freeing init memory: 6112K hub 1-0:1.0: /home/dev/org/SN986_1.60_QR_Scan_019a_20160606_0951/snx_sdk/kernel/linux-2.6.35.12/src/drivers/usb/core/hub.c 3351: state 7 ports 1 chg 0002 evt 0000 hub 1-0:1.0: port 1, status 0503, change 0000, 480 Mb/s snx_crypto driver loaded. sonix crypto diver register sonix_nvram_init kernel BUG at /home/dev/org/SN986_1.60_QR_Scan_019a_20160606_0951/snx_sdk/kernel/linux-2.6.35.12/src/arch/arm/mm/dma-mapping.c:415! Unable to handle kernel NULL pointer dereference at virtual address 00000000 fcse pid: 1, 0x02000000 pgd = c30c8000 [00000000] *pgd=030c5031, *pte=00000000, *ppte=00000000 Internal error: Oops: 817 [#1] last sysfs file: /sys/bus/platform/drivers/snx_crypto/uevent Modules linked in: snx_nvram(+) snx_crypto CPU: 0 Not tainted (2.6.35.12 #10) PC is at __bug+0x1c/0x28 LR is at __bug+0x18/0x28 pc : [] lr : [] psr: 60000013 sp : c30dbea0 ip : 0000ffff fp : 00000000 r10: c4870000 r9 : c30dbf24 r8 : 000003d0 r7 : 00000300 r6 : c3c4fc00 r5 : 00000000 r4 : 00fc0004 r3 : 00000000 r2 : c30dbe94 r1 : c09515f0 r0 : 0000008a Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user Control: 0005717f Table: 030c8000 DAC: 00000015 Process modprobe (pid: 456, stack limit = 0xc30da270) Stack: (0xc30dbea0 to 0xc30dc000) bea0: f0900000 c0606ac0 00fc0004 c074f1b4 c30dbec0 c09dc598 c3c4fe54 c3c4fe50 bec0: 22222222 c37d7e00 00000000 00000000 000003d0 00fc0000 00000000 00000000 bee0: 00012818 c0741e54 000003d0 c30dbf24 c4870000 00000000 00000004 00000000 bf00: c37d7e00 c0601288 c30da000 bf007390 000003d0 c30dbf24 c4870000 bf00b000 bf20: 00000000 00000000 00000000 bf008008 00000000 bf00b000 00000000 bf00b0c0 bf40: 000003d0 c4870000 00000000 000003d0 00000000 bf007ec0 00000000 c0600430 bf60: bf007ec0 bf007ec0 00000000 00056dc5 0000250c bf007ec0 00000000 00056dc5 bf80: 0000250c c0639118 0006b188 0000250c 00056dc5 0006a182 00000000 00000003 bfa0: 00000080 c06010e0 0006a182 00000000 0006b188 0000250c 00056dc5 00000000 bfc0: 0006a182 00000000 00000003 00000080 0006a191 00878008 00000024 00012818 bfe0: 0081c8fc 01a7781c 00011d34 0081c90c 20000010 0006b188 00000000 00000000 [] (__bug+0x1c/0x28) from [] (___dma_single_cpu_to_dev+0x34/0x5c) [] (___dma_single_cpu_to_dev+0x34/0x5c) from [] (snx_sf_read_dma+0x2f0/0x4a0) [] (snx_sf_read_dma+0x2f0/0x4a0) from [] (part_read+0x88/0xdc) [] (part_read+0x88/0xdc) from [] (sn_mtd_read_nm+0x4c/0x88 [snx_nvram]) [] (sn_mtd_read_nm+0x4c/0x88 [snx_nvram]) from [] (init_module+0xc0/0x1e4 [snx_nvram]) [] (init_module+0xc0/0x1e4 [snx_nvram]) from [] (do_one_initcall+0x60/0x1b4) [] (do_one_initcall+0x60/0x1b4) from [] (sys_init_module+0x90/0x1a4) [] (sys_init_module+0x90/0x1a4) from [] (ret_fast_syscall+0x0/0x2c) Code: e59f0010 e1a01003 eb0a9df8 e3a03000 (e5833000) ---[ end trace 4651a3089f9c0e32 ]--- usb 1-1: new high speed USB device using snx_ehci and address 2 usb 1-1: New USB device found, idVendor=0bda, idProduct=0179 usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 1-1: Product: 802.11n NIC usb 1-1: Manufacturer: Realtek usb 1-1: SerialNumber: 5CE04C9E97FE Sonix926 PWM diver register Sonix GPIO Driver RTL871X: module init start RTL871X: rtl8188eu v4.3.24_16705.20160509 RTL871X: build time: Jan 19 2017 06:53:17 RTL871X: usb_endpoint_descriptor(0): RTL871X: bLength=7 RTL871X: bDescriptorType=5 RTL871X: bEndpointAddress=81 RTL871X: wMaxPacketSize=512 RTL871X: bInterval=0 RTL871X: RT_usb_endpoint_is_bulk_in = 1 RTL871X: usb_endpoint_descriptor(1): RTL871X: bLength=7 RTL871X: bDescriptorType=5 RTL871X: bEndpointAddress=2 RTL871X: wMaxPacketSize=512 RTL871X: bInterval=0 RTL871X: RT_usb_endpoint_is_bulk_out = 2 RTL871X: usb_endpoint_descriptor(2): RTL871X: bLength=7 RTL871X: bDescriptorType=5 RTL871X: bEndpointAddress=3 RTL871X: wMaxPacketSize=512 RTL871X: bInterval=0 RTL871X: RT_usb_endpoint_is_bulk_out = 3 RTL871X: nr_endpoint=3, in_num=1, out_num=2

RTL871X: USB_SPEED_HIGH RTL871X: CHIP TYPE: RTL8188E RTL871X: rtw_hal_config_rftype RF_Type is 3 TotalTxPath is 1 RTL871X: Chip Version Info: CHIP_8188E_Normal_Chip_TSMC_D_CUT_1T1R_RomVer(0) RTL871X: _ConfigNormalChipOutEP_8188E OutEpQueueSel(0x05), OutEpNumber(2) RTL871X: EEPROM type is E-FUSE RTL871X: Boot from EFUSE, Autoload OK ! RTL871X: SetHwReg8188E: bMacPwrCtrlOn=1 bFWReady == _FALSE call reset 8051... RTL871X: =====> _8051Reset88E(): 8051 reset success . RTL871X: efuse_read_phymap_from_txpktbuf bcnhead:0 RTL871X: efuse_read_phymap_from_txpktbuf len:109, lenbak:109, aaa:109, aaabak:109 RTL871X: efuse_read_phymap_from_txpktbuf read count:107 RTL871X: EEPROM ID=0x8129 RTL871X: VID = 0x0BDA, PID = 0x0179 RTL871X: Customer ID: 0x00, SubCustomer ID: 0xCD RTL871X: Hal_ReadPowerSavingMode88E...bHWPwrPindetect(0)-bHWPowerdown(0) ,bSupportRemoteWakeup(1) RTL871X: ### PS params=> power_mgnt(0),usbss_enable(0) ### RTL871X: ======= Path 0, Channel 1 ======= RTL871X: Index24G_CCK_Base[0][1] = 0x2d RTL871X: Index24G_BW40_Base[0][1] = 0x2f RTL871X: ======= Path 0, Channel 2 ======= RTL871X: Index24G_CCK_Base[0][2] = 0x2d RTL871X: Index24G_BW40_Base[0][2] = 0x2f RTL871X: ======= Path 0, Channel 3 ======= RTL871X: Index24G_CCK_Base[0][3] = 0x2d RTL871X: Index24G_BW40_Base[0][3] = 0x2f RTL871X: ======= Path 0, Channel 4 ======= RTL871X: Index24G_CCK_Base[0][4] = 0x2d RTL871X: Index24G_BW40_Base[0][4] = 0x2f RTL871X: ======= Path 0, Channel 5 ======= RTL871X: Index24G_CCK_Base[0][5] = 0x2d RTL871X: Index24G_BW40_Base[0][5] = 0x2f RTL871X: ======= Path 0, Channel 6 ======= RTL871X: Index24G_CCK_Base[0][6] = 0x2c RTL871X: Index24G_BW40_Base[0][6] = 0x2e RTL871X: ======= Path 0, Channel 7 ======= RTL871X: Index24G_CCK_Base[0][7] = 0x2c RTL871X: Index24G_BW40_Base[0][7] = 0x2e RTL871X: ======= Path 0, Channel 8 ======= RTL871X: Index24G_CCK_Base[0][8] = 0x2c RTL871X: Index24G_BW40_Base[0][8] = 0x2e RTL871X: ======= Path 0, Channel 9 ======= RTL871X: Index24G_CCK_Base[0][9] = 0x2b RTL871X: Index24G_BW40_Base[0][9] = 0x2d RTL871X: ======= Path 0, Channel 10 ======= RTL871X: Index24G_CCK_Base[0][10] = 0x2b RTL871X: Index24G_BW40_Base[0][10] = 0x2d RTL871X: ======= Path 0, Channel 11 ======= RTL871X: Index24G_CCK_Base[0][11] = 0x2b RTL871X: Index24G_BW40_Base[0][11] = 0x2d RTL871X: ======= Path 0, Channel 12 ======= RTL871X: Index24G_CCK_Base[0][12] = 0x2a RTL871X: Index24G_BW40_Base[0][12] = 0x2c RTL871X: ======= Path 0, Channel 13 ======= RTL871X: Index24G_CCK_Base[0][13] = 0x2a RTL871X: Index24G_BW40_Base[0][13] = 0x2c RTL871X: ======= Path 0, Channel 14 ======= RTL871X: Index24G_CCK_Base[0][14] = 0x2a RTL871X: Index24G_BW40_Base[0][14] = 0x2c RTL871X: EEPROMRegulatory = 0x0 RTL871X: hal_com_config_channel_plan chplan:0x20 RTL871X: CrystalCap: 0x2c RTL871X: EEPROM Customer ID: 0x 0 RTL871X: EEPROM : AntDivCfg = 0, TRxAntDivType = 3 RTL871X: Board Type: 0x 0 RTL871X: ThermalMeter = 0x14 RTL871X: rtw_hal_read_chip_info in 560 ms RTL871X: init_channel_set((null)) ChannelPlan ID:0x20, ch num:13 RTL871X: NR_RECVBUFF: 8 RTL871X: MAX_RECVBUF_SZ: 4000 RTL871X: NR_PREALLOC_RECV_SKB: 16 RTL871X: Enable CONFIG_FIX_NR_BULKIN_BUFFER RTL871X: rtw_alloc_macid((null)) if1, hwaddr:ff:ff:ff:ff:ff:ff macid:1 RTL871X: rtw_macaddr_cfg mac addr:5c:ff:ff:9e:97:fe RTL871X: bDriverStopped:True, bSurpriseRemoved:False, bup:0, hw_init_completed:0 RTL871X: rtw_ndev_init(wlan0) if1 mac_addr=5c:ff:ff:9e:97:fe usbcore: registered new interface driver rtl8188eu RTL871X: module init ret=0 SNX_AUDIO: driver register. SNX_SIGMA: adc submod driver init ok. SNX_R2R: dac submod driver init ok. snx_isp snx_isp.0: [ISP] isp_camera_probe soc-camera-pdrv soc-camera-pdrv.0: Probing soc-camera-pdrv.0 scan:sc2135 sc2135 stop streaming 0x0103 = 0x00 0x0100 = 0x00 0x3e03 = 0x03 0x3e01 = 0x46 0x3e08 = 0x00 0x3e09 = 0x10 0x3416 = 0x11 0x3300 = 0x20 0x3301 = 0x08 0x3303 = 0x30 0x3306 = 0x78 0x330b = 0xd0 0x3309 = 0x30 0x3308 = 0x0a 0x331e = 0x26 0x331f = 0x26 0x3320 = 0x2c 0x3321 = 0x2c 0x3322 = 0x2c 0x3323 = 0x2c 0x330e = 0x20 0x3f05 = 0xdf 0x3f01 = 0x04 0x3626 = 0x04 0x3312 = 0x06 0x3340 = 0x03 0x3341 = 0x68 0x3342 = 0x02 0x3343 = 0x20 0x3333 = 0x10 0x3334 = 0x20 0x3621 = 0x18 0x3626 = 0x04 0x3635 = 0x34 0x3038 = 0xa4 0x3630 = 0x84 0x3622 = 0x0e 0x3620 = 0x62 0x3627 = 0x08 0x3637 = 0x87 0x3638 = 0x86 0x3034 = 0xd2 0x5780 = 0xff 0x5781 = 0x0c 0x5785 = 0x10 0x3d08 = 0x01 0x3640 = 0x00 0x3662 = 0x82 0x335d = 0x00 0x4501 = 0xa4 0x3333 = 0x00 0x3627 = 0x02 0x3620 = 0x62 0x5781 = 0x04 0x3333 = 0x10 0x3306 = 0x69 0x3635 = 0x52 0x3636 = 0x7c 0x3631 = 0x84 0x3637 = 0x88 0x3306 = 0x6b 0x330b = 0xd0 0x3630 = 0x84 0x303a = 0x07 0x3039 = 0x76 0x3343 = 0x40 0x3f04 = 0x02 0x3f05 = 0x04 0x3340 = 0x03 0x3341 = 0xe5 0x3207 = 0x4e 0x335d = 0x20 0x3368 = 0x02 0x3369 = 0x00 0x336a = 0x04 0x336b = 0x65 0x330e = 0x20 0x3367 = 0x05 0x3620 = 0x92 0x3634 = 0xd2 0x3633 = 0x17 0x3315 = 0x02 0x3334 = 0xa0 0x3312 = 0x00 0x335e = 0x02 0x335f = 0x0a 0x3306 = 0x60 0x3f04 = 0x01 0x3f05 = 0xf7 0x303a = 0x15 0x3039 = 0x2e 0x3035 = 0x25 0x3034 = 0x2e 0x3036 = 0x00 0x320c = 0x04 0x320d = 0x65 0x320e = 0x04 0x320f = 0xb0 0x3368 = 0x02 0x3369 = 0x4b 0x363a = 0x04 0x336b = 0xb0 0x3306 = 0x70 0x3640 = 0x01 0x3034 = 0x2e 0x3633 = 0x16 0x3211 = 0x14 sensor:sc2135 (id:0x2135) driver loadded sc2135 start streaming IQ.bin OK! ubIdx = 11, fps = 20 priv->uwMaxExpL = 1800, info->frame_rate = 20 snx_isp snx_isp.0: ISP Camera driver loaded snx_vc snx_vc: sonix_vc device registered as /dev/video1 snx_vc snx_vc: sonix_vc device registered as /dev/video1 snx_vc snx_vc: sonix_vc device registered as /dev/video2 snx_vc snx_vc: sonix_vc device registered as /dev/video2 snx_sd_initial:1377: SD initialisation done. mmc_rescan:1159 = 0 mmc0: new high speed SDHC card at address 0007 mmc_add_card:259 = 0 mmcblk0: mmc0:0007 SD16G 14.4 GiB mmcblk0: p1 p2 mmc_add_card:265 = 0 st58660_udc init: version V1.0.0 st58660_udc_probe irq num = 9 U2 Connect interrupt starting pid 599, tty '/dev/ttyS0': '/sbin/getty -L ttyS0 115200 vt100'

(none) login: root Password: ismart12 ~ #