2021-06-07
A bridged wireless access point (aka Dumb AP) works within an existing ethernet network to add WiFi capability where it does not exist or to extend the network to WiFi capable computers and devices in areas where the WiFi signal is weak or otherwise does not meet expectations.
This document outlines single band and dual band WiFi setups using a Raspberry Pi 3B, 3B+ or 4B with an AC1200 or above USB 3 WiFi adapter for 5 GHz band and either an additional external WiFi adapter or internal WiFi for 2.4 GHz band. There is a lot of flexibility and capability available with this type of setup.
This setup supports WPA3-SAE. It is disabled by default.
WPA3-SAE will not work with Realtek 88xx chipset based USB WiFi adapters.
WPA3-SAE will work with Mediatek 761x chipset based USB WiFI adapters.
Note: This guide uses systemd-networkd for network management. If your Linux distro uses Network Manager or Netplan, they must be disabled. Sections that explain how to do this are located near the end of this document. Please go to and follow the appropriate section now, if required, before continuing with this setup guide.
Raspberry Pi OS (2021-05-07) (32 bit) (kernel 5.10.17-v7l+)
Ethernet connection providing internet
Note: I use the case upside down. There are several little things that work better with the case upside down and no negatives that I can find.
Note: Very few Powered USB 3 Hubs will work well with Raspberry Pi hardware. The primary problem has to do with the backfeeding of current into the Raspberry Pi. One that seems to work well here is:
Transcend USB 3.0 4-Port Hub TS-HUB3K
Note: The rtl88XXxu chipset based USB3 WiFi adapters require from 504 mA of power up to well over 800 mA of power depending on the adapter. The Raspberry Pi 3B, 3B+ and 4B USB subsystems are only able to supple a total of 1200 mA of power to all attached devices.
Note: The Alfa AWUS036ACM adapter, a mt7612u based adapter, requests a maximum of 400 mA from the USB subsystem during initialization. Testing with a meter shows actual usage of 360 mA during heavy load and usage of 180 mA during light loads. This is much lower power usage than most AC1200 class adapters which makes this adapter a good choice for a Raspberry Pi based access point.
USB WiFi adapter driver installation, if required, should be performed and tested prior to continuing.
Note: For USB3 adapters based on the Realtek rtl8812au, rtl8814au, and rtl8812bu chipsets, the following module parameters may be needed for best performance when the adapter is set to support 5 GHz band:
rtw_vht_enable=2 rtw_switch_usb_mode=1
Note: For USB3 adapters based on the Realtek rtl8812au, rtl8814au, and rtl8812bu chipsets, the following module parameters may be needed for best performance when the adapter is set to support 2.4 GHz band:
rtw_vht_enable=1 rtw_switch_usb_mode=2
Note: For USB3 adapters based on Mediatek mt7612u or my7612un chipsets, the following module parameter may be needed for best performance:
disable_usb_sg=1
Note: For this access point setup to support WPA3-SAE in a dual band setup, two USB WiFi adapters with Mediatek or Atheros chipsets are required as the Realtek and internal Raspberry Pi WiFi drivers do not support WPA3-SAE as of the date of this document.
The follow site provides links to adapters that support WPA3-SAE: USB-WIFI
Update system.
sudo apt update
Upgrade system.
sudo apt full-upgrade
Note: Upgrading system is not mandatory for this installation but since some users forget to upgrade their system on a regular basis, maybe it is a good idea.
Reduce overall power consumption and overclock the CPU a modest amount.
Note: All items in this step are optional and some items are specific to the Raspberry Pi 4B. If installing to a Raspberry Pi 3b or 3b+ you will need to use the appropriate settings for that hardward.
sudo nano /boot/config.txt
Change
# turn off onboard audio
dtparam=audio=off
# disable DRM VC4 V3D driver on top of the dispmanx display stack
#dtoverlay=vc4-fkms-v3d
#max_framebuffers=2
Add
# turn off Mainboard LEDs
dtoverlay=act-led
# disable Activity LED
dtparam=act_led_trigger=none
dtparam=act_led_activelow=off
# disable Power LED
dtparam=pwr_led_trigger=none
dtparam=pwr_led_activelow=off
# turn off Ethernet port LEDs
dtparam=eth_led0=4
dtparam=eth_led1=4
# turn off Bluetooth
dtoverlay=disable-bt
# turn off onboard WiFi
dtoverlay=disable-wifi
# overclock CPU
over_voltage=1
arm_freq=1600
Enable predictable network interface names
Note: While this step is optional, problems can arise without it on dual band setups. Some operating systems have this capability enabled by default but not the Raspberry Pi OS.
sudo raspi-config
Select: Advanced options > A4 Network Interface Names > Yes
Reboot system.
sudo reboot
Determine name and state of the network interfaces.
ip a
You may need to additionally run the following commands in order to determine which adapter, in a dual band setup, has which interface name.
iw list
iw dev
Note: If the interface names are not eth0, wlan0 and wlan1,
then the interface names used in your system will have to replace
eth0, wlan0 and wlan1 for the remainder of this document.
Install needed package. Website - hostapd
sudo apt install hostapd
Enable the wireless access point service and set it to start when your Raspberry Pi boots.
sudo systemctl unmask hostapd
sudo systemctl enable hostapd
Note: The below steps include creating two hostapd configurations files but only one is needed if using a single band setup.
Create hostapd configuration file for 5 GHz band.
sudo nano /etc/hostapd/hostapd-5g.conf
File contents
# /etc/hostapd/hostapd-5g.conf
# Documentation: https://w1.fi/cgit/hostap/plain/hostapd/hostapd.conf
# 2021-05-30
# SSID
ssid=myPI-5g
# PASSPHRASE
wpa_passphrase=myPW1234
# Band: a = 5g (a/n/ac), g = 2g (b/g/n)
hw_mode=a
# Channel
channel=36
# Country
country_code=US
# WiFi interface
interface=wlan0
# Bridge interface
bridge=br0
driver=nl80211
ctrl_interface=/var/run/hostapd
ctrl_interface_group=0
ieee80211d=1
ieee80211h=1
beacon_int=100
dtim_period=2
max_num_sta=32
macaddr_acl=0
rts_threshold=2347
fragm_threshold=2346
#send_probe_response=1
# security
auth_algs=1
ignore_broadcast_ssid=0
# wpa=2 is required for WPA2 and WPA3 (read the docs)
wpa=2
rsn_pairwise=CCMP
# only one wpa_key_mgmt= line should be active.
# wpa_key_mgmt=WPA-PSK is required for WPA2-AES
wpa_key_mgmt=WPA-PSK
# wpa_key_mgmt=SAE WPA-PSK is required for WPA3-AES Transitional
#wpa_key_mgmt=SAE WPA-PSK
# wpa_key_mgmt=SAE is required for WPA3-SAE
#wpa_key_mgmt=SAE
#wpa_group_rekey=1800
# ieee80211w=1 is required for WPA-3 SAE Transitional
# ieee80211w=2 is required for WPA-3 SAE
#ieee80211w=1
# if parameter is not set, 19 is the default value.
#sae_groups=19 20 21 25 26
# sae_require_mfp=1 is required for WPA-3 SAE Transitional
#sae_require_mfp=1
# if parameter is not 9 set, 5 is the default value.
#sae_anti_clogging_threshold=10
# Note: Capabilities can vary even between adapters with the same chipset.
#
# Note: Only one ht_capab= line and one vht_capab= should be active. The
# content of these lines is determined by the capabilities of your adapter.
#
# IEEE 802.11n
ieee80211n=1
wmm_enabled=1
#
# mt7612u - mt7610u
#ht_capab=[HT40+][HT40-][GF][SHORT-GI-20][SHORT-GI-40]
#
# rtl8812au - rtl8811au - rtl8812bu - rtl8811cu - rtl8814au
ht_capab=[HT40+][HT40-][SHORT-GI-20][SHORT-GI-40][MAX-AMSDU-7935]
#
# IEEE 802.11ac
ieee80211ac=1
#
# mt7610u
#vht_capab=[SHORT-GI-80][MAX-A-MPDU-LEN-EXP3][RX-ANTENNA-PATTERN][TX-ANTENNA-PATTERN]
# mt7612u
#vht_capab=[RXLDPC][SHORT-GI-80][TX-STBC-2BY1][RX-STBC-1][MAX-A-MPDU-LEN-EXP3][RX-ANTENNA-PATTERN][TX-ANTENNA-PATTERN]
#
# rtl8812au - rtl8811au - rtl8812bu - rtl8811cu - rtl8814au
vht_capab=[MAX-MPDU-11454][SHORT-GI-80][HTC-VHT]
# Note: [TX-STBC-2BY1] causes problems
#
# Required for 80 MHz width channel operation
vht_oper_chwidth=1
#
# Use the next line with channel 36 (36 + 6 = 42)
vht_oper_centr_freq_seg0_idx=42
#
# Use the next line with channel 149 (149 + 6 = 155)
#vht_oper_centr_freq_seg0_idx=155
# Event logger - as desired
#logger_syslog=-1
#logger_syslog_level=2
#logger_stdout=-1
#logger_stdout_level=2
# WMM - as desired
#uapsd_advertisement_enabled=1
#wmm_ac_bk_cwmin=4
#wmm_ac_bk_cwmax=10
#wmm_ac_bk_aifs=7
#wmm_ac_bk_txop_limit=0
#wmm_ac_bk_acm=0
#wmm_ac_be_aifs=3
#wmm_ac_be_cwmin=4
#wmm_ac_be_cwmax=10
#wmm_ac_be_txop_limit=0
#wmm_ac_be_acm=0
#wmm_ac_vi_aifs=2
#wmm_ac_vi_cwmin=3
#wmm_ac_vi_cwmax=4
#wmm_ac_vi_txop_limit=94
#wmm_ac_vi_acm=0
#wmm_ac_vo_aifs=2
#wmm_ac_vo_cwmin=2
#wmm_ac_vo_cwmax=3
#wmm_ac_vo_txop_limit=47
#wmm_ac_vo_acm=0
# TX queue parameters - as desired
#tx_queue_data3_aifs=7
#tx_queue_data3_cwmin=15
#tx_queue_data3_cwmax=1023
#tx_queue_data3_burst=0
#tx_queue_data2_aifs=3
#tx_queue_data2_cwmin=15
#tx_queue_data2_cwmax=63
#tx_queue_data2_burst=0
#tx_queue_data1_aifs=1
#tx_queue_data1_cwmin=7
#tx_queue_data1_cwmax=15
#tx_queue_data1_burst=3.0
#tx_queue_data0_aifs=1
#tx_queue_data0_cwmin=3
#tx_queue_data0_cwmax=7
#tx_queue_data0_burst=1.5
# end of hostapd-5g.conf
Create the 2g hostapd configuration file.
sudo nano /etc/hostapd/hostapd-2g.conf
File contents
# /etc/hostapd/hostapd-2g.conf
# Documentation: https://w1.fi/cgit/hostap/plain/hostapd/hostapd.conf
# 2021-05-30
# SSID
ssid=myPI-2g
# PASSPHRASE
wpa_passphrase=myPW1234
# Band: a = 5g (a/n/ac), g = 2g (b/g/n)
hw_mode=g
# Channel
channel=6
# Country
country_code=US
# WiFi interface
interface=wlan1
# Bridge interface
bridge=br0
driver=nl80211
ctrl_interface=/var/run/hostapd
ctrl_interface_group=0
beacon_int=100
dtim_period=2
max_num_sta=32
rts_threshold=2347
fragm_threshold=2346
#send_probe_response=1
# security
auth_algs=1
macaddr_acl=0
ignore_broadcast_ssid=0
wpa=2
wpa_pairwise=CCMP
# WPA-2 AES
wpa_key_mgmt=WPA-PSK
# WPA-3 SAE
#wpa_key_mgmt=SAE
#wpa_group_rekey=1800
rsn_pairwise=CCMP
# ieee80211w=2 is required for WPA-3 SAE
#ieee80211w=2
# If parameter is not set, 19 is the default value.
#sae_groups=19 20 21 25 26
#sae_require_mfp=1
# If parameter is not 9 set, 5 is the default value.
#sae_anti_clogging_threshold=10
# IEEE 802.11n
ieee80211n=1
wmm_enabled=1
#
# Note: Only one ht_capab= line should be active. The content of these lines is
# determined by the capabilities of your adapter.
#
# ar9271
#ht_capab=[HT40+][HT40-][SHORT-GI-20][SHORT-GI-40][RX-STBC1][DSSS_CCK-40]
#
# mt7612u - mt7610u
#ht_capab=[HT40+][HT40-][GF][SHORT-GI-20][SHORT-GI-40]
#
# rtl8812au - rtl8811au - rtl8812bu - rtl8811cu - rtl8814au
ht_capab=[HT40+][HT40-][SHORT-GI-20][SHORT-GI-40][MAX-AMSDU-7935]
# Event logger - as desired
#logger_syslog=-1
#logger_syslog_level=2
#logger_stdout=-1
#logger_stdout_level=2
# WMM - as desired
#uapsd_advertisement_enabled=1
#wmm_ac_bk_cwmin=4
#wmm_ac_bk_cwmax=10
#wmm_ac_bk_aifs=7
#wmm_ac_bk_txop_limit=0
#wmm_ac_bk_acm=0
#wmm_ac_be_aifs=3
#wmm_ac_be_cwmin=4
#wmm_ac_be_cwmax=10
#wmm_ac_be_txop_limit=0
#wmm_ac_be_acm=0
#wmm_ac_vi_aifs=2
#wmm_ac_vi_cwmin=3
#wmm_ac_vi_cwmax=4
#wmm_ac_vi_txop_limit=94
#wmm_ac_vi_acm=0
#wmm_ac_vo_aifs=2
#wmm_ac_vo_cwmin=2
#wmm_ac_vo_cwmax=3
#wmm_ac_vo_txop_limit=47
#wmm_ac_vo_acm=0
# TX queue parameters - as desired
#tx_queue_data3_aifs=7
#tx_queue_data3_cwmin=15
#tx_queue_data3_cwmax=1023
#tx_queue_data3_burst=0
#tx_queue_data2_aifs=3
#tx_queue_data2_cwmin=15
#tx_queue_data2_cwmax=63
#tx_queue_data2_burst=0
#tx_queue_data1_aifs=1
#tx_queue_data1_cwmin=7
#tx_queue_data1_cwmax=15
#tx_queue_data1_burst=3.0
#tx_queue_data0_aifs=1
#tx_queue_data0_cwmin=3
#tx_queue_data0_cwmax=7
#tx_queue_data0_burst=1.5
# End of hostapd-2g.conf
Establish hostapd conf file and log file locations.
Note: Make sure to change <your_home> to your home directory.
sudo nano /etc/default/hostapd
Select one of the following options
Dual band option: Add to bottom of file
DAEMON_CONF="/etc/hostapd/hostapd-5g.conf /etc/hostapd/hostapd-2g.conf"
DAEMON_OPTS="-d -K -f /home/<your_home>/hostapd.log"
Single band option for 5g: Add to bottom of file
DAEMON_CONF="/etc/hostapd/hostapd-5g.conf"
DAEMON_OPTS="-d -K -f /home/<your_home>/hostapd.log"
Single band option for 2g: Add to bottom of file
DAEMON_CONF="/etc/hostapd/hostapd-2g.conf"
DAEMON_OPTS="-d -K -f /home/<your_home>/hostapd.log"
Modify hostapd.service file.
Code:
sudo cp /usr/lib/systemd/system/hostapd.service /etc/systemd/system/hostapd.service
sudo nano /etc/systemd/system/hostapd.service
Select one of the following options
Dual band option: Change the 'Environment=' line and 'ExecStart=' line to the following
Environment=DAEMON_CONF="/etc/hostapd/hostapd-5g.conf /etc/hostapd/hostapd-2g.conf"
ExecStart=/usr/sbin/hostapd -B -P /run/hostapd.pid -B $DAEMON_OPTS $DAEMON_CONF
Single band option for 5g: Change the 'Environment=' line and 'ExecStart=' line to the following
Environment=DAEMON_CONF="/etc/hostapd/hostapd-5g.conf"
ExecStart=/usr/sbin/hostapd -B -P /run/hostapd.pid -B $DAEMON_OPTS $DAEMON_CONF
Single band option for 2g: Change the 'Environment=' line and 'ExecStart=' line to the following
Environment=DAEMON_CONF="/etc/hostapd/hostapd-2g.conf"
ExecStart=/usr/sbin/hostapd -B -P /run/hostapd.pid -B $DAEMON_OPTS $DAEMON_CONF
Block the eth0, wlan0 qnd wlan1 interfaces from being processed, and let dhcpcd configure only br0 via DHCP.
sudo nano /etc/dhcpcd.conf
Add the following line above the first interface xxx line, if any, for dual band setup
denyinterfaces eth0 wlan0 wlan1
Add the following line above the first interface xxx line, if any, for single band setup
denyinterfaces eth0 wlan0
Go to the end of the file and add the following line
interface br0
Enable systemd-networkd service. Website - systemd-network
sudo systemctl enable systemd-networkd
Create bridge interface br0.
sudo nano /etc/systemd/network/10-bridge-br0-create.netdev
File contents
[NetDev]
Name=br0
Kind=bridge
Bind ethernet interface.
sudo nano /etc/systemd/network/20-bridge-br0-bind-ethernet.network
File contents
[Match]
Name=eth0
[Network]
Bridge=br0
Configure bridge interface.
sudo nano /etc/systemd/network/21-bridge-br0-config.network
Note: The contents of the Network block below should reflect the needs of your network.
File contents
[Match]
Name=br0
[Network]
Address=192.168.1.100/24
Gateway=192.168.1.1
DNS=8.8.8.8
Ensure WiFi radio not blocked.
sudo rfkill unblock wlan
Reboot system.
sudo reboot
End of installation.
Notes:
Restart systemd-networkd service.
sudo systemctl restart systemd-networkd
Check status of the services.
systemctl status hostapd
systemctl status systemd-networkd
Autostarting iperf3
sudo apt install iperf3
sudo nano /etc/systemd/system/iperf3.service
File contents
[Unit]
Description=iPerf3 Service
After=syslog.target network.target auditd.service
[Service]
Type=simple
ExecStart=/usr/bin/iperf3 -s
[Install]
WantedBy=multi-user.target
sudo systemctl enable iperf3
Check iperf3 status
sudo systemctl status iperf3
Disable NetworkManager
Note: For systems not running the Gnome desktop, purging Network Manager is the easiest solution.
sudo apt purge network-manager
Note: For systems running the Gnome desktop, use the following.
sudo systemctl stop NetworkManager.service
sudo systemctl disable NetworkManager.service
sudo systemctl stop NetworkManager-wait-online.service
sudo systemctl disable NetworkManager-wait-online.service
sudo systemctl stop NetworkManager-dispatcher.service
sudo systemctl disable NetworkManager-dispatcher.service
sudo systemctl stop network-manager.service
sudo systemctl disable network-manager.service
sudo reboot
Disable Netplan
Note: Netplan is the default network manager on Ubuntu server.
Disable and mask networkd-dispatcher.
Note: we are activating /etc/network/interfaces
sudo apt-get install ifupdown
sudo systemctl stop networkd-dispatcher
sudo systemctl disable networkd-dispatcher
sudo systemctl mask networkd-dispatcher
Purge netplan.
sudo apt-get purge nplan netplan.io
sudo reboot