-
Notifications
You must be signed in to change notification settings - Fork 4
/
eeprom_settings.txt
90 lines (76 loc) · 3 KB
/
eeprom_settings.txt
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
########################################################################
# EEPROM settings text file
#
# Edit this file for your particular board and run through eepmake tool,
# then use eepflash tool to write to attached HAT ID EEPROM
#
# Tools available:
# eepmake Parses EEPROM text file and creates binary .eep file
# eepdump Dumps a binary .eep file as human readable text (for debug)
# eepflash Write or read .eep binary image to/from HAT EEPROM
#
########################################################################
########################################################################
# Vendor info
# 128 bit UUID. If left at zero eepmake tool will auto-generate
# RFC 4122 compliant UUID
product_uuid ee512f24-abab-4c34-9cbc-86a773b99fee
# 16 bit product id
product_id 0xca10
# 16 bit product version
product_ver 0x0001
# ASCII vendor string (max 255 characters)
vendor "Gregor Riepl <[email protected]>"
# ASCII product string (max 255 characters)
product "CAN HAT"
########################################################################
# GPIO bank settings, set to nonzero to change from the default.
# NOTE these setting can only be set per BANK, uncommenting any of
# these will force the bank to use the custom setting.
# drive strength, 0=default, 1-8=2,4,6,8,10,12,14,16mA, 9-15=reserved
gpio_drive 0
# 0=default, 1=slew rate limiting, 2=no slew limiting, 3=reserved
gpio_slew 0
# 0=default, 1=hysteresis disabled, 2=hysteresis enabled, 3=reserved
gpio_hysteresis 0
# If board back-powers Pi via 5V GPIO header pins:
# 0 = board does not back-power
# 1 = board back-powers and can supply the Pi with a minimum of 1.3A
# 2 = board back-powers and can supply the Pi with a minimum of 2A
# 3 = reserved
# If back_power=2 then USB high current mode will be automatically
# enabled on the Pi
back_power 0
########################################################################
# GPIO pins, uncomment for GPIOs used on board
# Options for FUNCTION: INPUT, OUTPUT, ALT0-ALT5
# Options for PULL: DEFAULT, UP, DOWN, NONE
# NB GPIO0 and GPIO1 are reserved for ID EEPROM so cannot be set
# GPIO FUNCTION PULL
# ---- -------- ----
#setgpio 2 INPUT DEFAULT
#setgpio 3 INPUT DEFAULT
#setgpio 4 INPUT DEFAULT
#setgpio 5 INPUT DEFAULT
#setgpio 6 INPUT DEFAULT
#setgpio 7 INPUT DEFAULT
#setgpio 8 INPUT DEFAULT
#setgpio 9 INPUT DEFAULT
#setgpio 10 INPUT DEFAULT
#setgpio 11 INPUT DEFAULT
setgpio 12 INPUT NONE
#setgpio 13 INPUT DEFAULT
#setgpio 14 INPUT DEFAULT
#setgpio 15 INPUT DEFAULT
#setgpio 16 INPUT DEFAULT
#setgpio 17 INPUT DEFAULT
#setgpio 18 INPUT DEFAULT
#setgpio 19 INPUT DEFAULT
#setgpio 20 INPUT DEFAULT
#setgpio 21 INPUT DEFAULT
#setgpio 22 INPUT DEFAULT
#setgpio 23 INPUT DEFAULT
#setgpio 24 INPUT DEFAULT
#setgpio 25 INPUT DEFAULT
#setgpio 26 INPUT DEFAULT
#setgpio 27 INPUT DEFAULT