Skip to content

Latest commit

 

History

History
120 lines (96 loc) · 5.88 KB

prim_prince.md

File metadata and controls

120 lines (96 loc) · 5.88 KB
Raw

Primitive Component: PRINCE Scrambler

Overview

prim_prince is an (unhardened) implementation of the 64bit PRINCE block cipher. It is a fully unrolled combinational implementation with a configurable number of rounds (data and key state registers placed half-way in the design can optionally be enabled). Due to the mirrored construction of this cipher, the same circuit can be used for encryption and decryption, as described below. Further, the primitive supports a 32bit block cipher flavor which is not specified in the original paper.

It should be noted, however, that reduced-round and/or 32bit versions are not secure and must not be used in a setting where cryptographic cipher strength is required. I.e., this primitive is only intended to be used as a lightweight data scrambling device.

This paper compares several lightweight ciphers, where PRINCE has been found to be the fastest candidate with the lowest circuit complexity among the algorithms compared.

Parameters

Name type Description
DataWidth int Block size, can be 32 or 64.
KeyWidth int Key size, can be 64 for block size 32, or 128 for block size 64
NumRounds int Half the number of the reflected PRINCE rounds. Can range from 1 to 5. The effective number of non-linear layers is 2 + 2 * NumRounds.
UseOldKeySched bit If set to 1, fall back to the original keyschedule (not recommended). Defaults to 0.
HalfwayDataReg bit If set to 1, instantiates a data register half-way in the data path
HalfwayKeyReg bit If set to 1, instantiates a key register half-way in the data path. This is only required if the key is not static and changes with every new data input.

Signal Interfaces

Name In/Out Description
clk_i input Clock input
rst_ni input Reset input
valid_i input Data valid input
data_i input Plaintext input
data_i input Plaintext input
key_i input Key input
dec_i input Assert for decryption
valid_o output Data valid output
data_o output Output of the ciphertext

Theory of Operations

               /-----------------\
clk_i / rst_ni |                 |
-------------->|                 |
dec_i          |                 |
-------------->|     PRINCE      |
valid_i        |                 | valid_o
-------------->|    DataWidth    |--------------->
key_i          |    KeyWidth     |
=====/========>|    NumRounds    |
 [KeyWidth]    |  UseOldKeySched | data_o
               |  HalfwayDataReg |=======/=======>
data_i         |  HalfwayKeyReg  | [DataWidth]
=====/========>|                 |
 [DataWidth]   |                 |
               |                 |
               \-----------------/

The PRINCE module is fully unrolled and combinational by default. But since data and key state registers can optionally be enabled, the primitive also has a clock, reset and valid input besides the key and plaintext inputs. On the output side it exposes the ciphertext with its corresponding valid signal.

The internal construction follows the algorithm described in the original paper. The block size is 64bit and the key size is 128bit. In its original formulation, this cipher has 11 rounds (but 12 non-linear layers), which are arranged in a mirrored structure, which allows the same circuit to be used for encryption and decryption with a lightweight tweak applied to the key:

k0, k0_prime, k1 = key_derivation(key_i, dec_i);

// decryption mode
if (dec_i) {
      swap(k0, k0_prime);
      k1 ^= ALPHA_CONSTANT;
}

state = data_i ^ k0;

state ^= k1;
state ^= ROUND_CONSTANT[0];

// forward pass
for (int i=1; i < 6; i++) {
      state = sbox4_layer(state);
      state = mult_layer(state);
      state = shiftrows_layer(state);
      state ^= ROUND_CONSTANT[i]
      data_state ^= (k & 0x1) ? k0 : k1;
}

// middle part
state = sbox4_layer(state);
state = mult_layer(state);
state = sbox4_inverse_layer(state);

// reverse pass
for (int i=6; i < 11; i++) {
      data_state ^= (k & 0x1) ? k1 : k0;
      state ^= ROUND_CONSTANT[i]
      state = shiftrows_inverse_layer(state);
      state = mult_layer(state);
      state = sbox4_inverse_layer(state);
}

state ^= ROUND_CONSTANT[11];
state ^= k1;

data_o = state ^ k0_prime;

The multiplicative layer is an involution, meaning that it is its own inverse and it can hence be used in the reverse pass without inversion.

It should be noted that the actual choice of the ALPHA_CONSTANT used in the key tweak can have security impacts as detailed in this paper. The constant chosen by the designers of PRINCE does not have these issues - but proper care should be taken if it is decided to modify this constant. Also, this paper proposes an improved key schedule to fend against attacks on the FX structure of PRINCE (see Appendix C), and this improvement has been incorporated in this design. The improvement involves alternating the keys k0 and k1 between rounds, as opposed to always using the same key k1.

The reduced 32bit variant mentioned above and all reduced round variants are non-standard and must only be used for scrambling purposes, since they are not secure. The 32bit variant leverages the same crypto primitives and key derivation functions as the 64bit variant, with the difference that the multiplication matrix is only comprised of the first two block diagonal submatrices (^M0 and ^M1 in the paper), and the shiftrows operation does not operate on nibbles but pairs of 2 bits instead.