dump1090-fa can optionally tune the receiver gain automatically to try to pick a gain value for the particular hardware and RF environment without manual tuning. This README covers some of the background for why this is useful, and how to configure dump1090 to enable this feature.
In general, more receiver gain means better reception. Most ADS-B transmitters within line of sight transmit with enough power that their messages can potentially be decoded, but if the receiver gain setting is too low then very weak signals may still be too weak to be decoded even after amplification. Adding extra receiver gain helps in this case.
However, there are two problems with just adding more gain to a wideband SDR. First, everything is amplified, not only the signals of interest. Noise and RF interference is also amplified. At high gain settings or in noisy RF environments, this can interfere with receiving the ADS-B signals themselves.
Second, there is a wide range of possible ADS-B signal strengths. There can be a 60dB or more difference between the weakest signals (a distant aircraft at the limit of receiver range) and the strongest signals (a nearby aircraft on the ramp 100m from the receiver). Increasing the receiver gain to handle the weakest signals can mean that the strongest signals overload the receiver. A rtlsdr receiver only has about 30-35dB of dynamic range available at a particular gain setting, so there is no single gain setting that can simultaneously handle both the weakest and strongest signals.
Adaptive gain tries to deal with these cases by changing the receiver gain on the fly to handle the signal and noise levels that are currently being seen without human intervention. It is not perfect and it's not a substitute for hand-tuning of gain settings, but it aims at picking a reasonable setting for cases where individual hand-tuning isn't possible.
How to configure adaptive gain varies depending on how you have installed dump1090.
If you are using a PiAware sdcard image, adaptive gain can be configured by
editing /boot/piaware-config.txt or by using the piaware-config command.
If you are using the Debian package, adaptive gain can be configured by editing
/etc/default/dump1090-fa.
If running dump1090 directly, adaptive gain options are set directly by command-line options.
For new PiAware or Debian package installations, adaptive dynamic range mode is enabled by default and adaptive burst mode is disabled by default.
For upgrades of PiAware or the Debian package from versions older than 6.0, both adaptive gain modes are disabled by default.
These defaults can be overridden as described below.
The dynamic range adaptive gain mode attempts to set the receiver gain to maintain a given dynamic range - that is, it tries to set the gain so that general noise is at or below a given level. This takes into account different or changing RF environments and different receiver hardware (antenna, preamplifiers, etc) that affects the overall gain of the system, and usually will pick a reasonable gain setting without intervention.
To enable this mode:
- Set
adaptive-dynamic-range yesin piaware-config; or - Set
ADAPTIVE_DYNAMIC_RANGE=yesin/etc/default/dump1090-fa; or - Pass the
--adaptive-rangeoption on the command line.
The default settings for dynamic range will use a dynamic range target chosen based on SDR type (e.g. 30dB for rtlsdr receivers). This is usually a good default. To override this target:
- Set
adaptive-dynamic-range-targetin piaware-config; or - Set
ADAPTIVE_DYNAMIC_RANGE_TARGETin/etc/default/dump1090-fa; or - Pass the
--adaptive-range-targetoption on the command line.
The "burst" adaptive gain mode listens for loud bursts of signal that were not successfully decoded as ADS-B messages, but which have approximately the right timing to be possible messages that were lost due to receiver overloading. When enough overly-loud signals are heard in a short period of time, dump1090 will reduce the receiver gain to try to allow them to be received.
This is a more situational setting. It may allow reception of loud nearby aircraft (e.g. if you are close to an airport). The tradeoff is that when there are nearby aircraft, overall receiver range may be reduced. Whether this is a good tradeoff depends on the aircraft you're interested in. By default, adaptive gain burst mode is disabled.
To enable burst mode:
- Set
adaptive-burst yesin piaware-config; or - Set
ADAPTIVE_BURST=yesin/etc/default/dump1090-fa; or - Pass the
--adaptive-burstoption on the command line.
This mode is more experimental than the dynamic range mode and tweaking of
the advanced burst options may be needed depending on your local installation.
In particular, --adaptive-burst-loud-rate and adaptive-burst-quiet-rate
may need adjusting. Feedback on what works for you and what doesn't would
be appreciated!
Burst mode and dynamic range mode can be enabled at the same time.
If you know in advance approximately what the gain setting should be, so you want to allow adaptive gain to change the gain only within a certain range, you can set minimum and maximum gain settings in dB. Adaptive gain will only adjust the gain within this range. To set this:
- Set
adaptive-min-gainandadaptive-max-gainin piaware-config; or - Set
ADAPTIVE_MIN_GAINandADAPTIVE_MAX_GAINin/etc/default/dump1090-fa; or - Pass the
--adaptive-min-gainand--adaptive-max-gainoptions on the command line.
If you know approximately where the gain should be, then a good starting point would be to set the max and min adaptive gain to +/- 10dB around your gain setting.
The measurements needed to adjust gain have a CPU cost, and on slower devices it may be useful to reduce the amount of work that adaptive gain does. This can be done by adjusting the adaptive gain duty cycle. This is a percentage that controls what fraction of incoming data adaptive gain inspects. 100% means that every sample is inspected. Lower values reduce CPU use, with a tradeoff that adaptive gain has a less accurate picture of the RF environment. The default duty cycle is 50% on "fast" CPUs and 10% on "slow" CPUs (where currently "slow" means "armv6 architecture", for example the Pi Zero or Pi 1). To reduce the duty cycle further:
- Set
slow-cpu yesin piaware-config; or - Set
SLOW_CPU=yesin/etc/default/dump1090-fa; or - Pass the
--adaptive-duty-cycleoption on the command line
There are a number of advanced options that are only supported as
command-line options or via the EXTRA_OPTIONS setting in
/etc/default/dump1090-fa. They tweak settings that require some knowledge of
dump1090 internals to make sense of, so YMMV.
For a complete list of options, run dump1090-fa --help and look at the
adaptive gain section.
Currently, adaptive gain is only supported on rtlsdr devices. Support for other SDRs is planned for the future.
If you're a developer and want to add support for your SDR, you'll need
to implement the gain control API used in sdr.[ch]. See sdr_rtlsdr.c
(rtlsdrGetGain, rtlsdrSetGain, etc) for examples.
There is an auto-gain script written by wiedehopf that aims to solve similar problems. The implementation approaches are quite different, and which one works best for you will depend on the problem you're trying to solve.
The major differences between adaptive gain and the auto-gain script are:
-
Adaptive gain works on short-term data (seconds or minutes) and can react to changes in a similar timeframe. It tries to set an appropriate gain for the current environment without much regard for longer-term trends. The auto-gain script looks at data over longer timeframes (1+ days) and reacts more slowly, but takes into account data across that whole period.
-
Adaptive gain in dynamic range mode looks at an estimate of the noise floor to decide whether to increase gain. Adaptive gain in burst mode looks at the signal strength of samples that were not successfully decoded to decide when to reduce gain. The auto-gain scripts look at the signal strength of successfully decoded messages to decide when to increase or decrease gain. These are each measuring something different, and which is most effective will depend on the exact RF environment.
-
Adaptive gain burst mode and the auto-gain script superfically measure similar things, but the difference in measurement timeframe mean they react quite differently. Burst mode tries to react to transient loud signals i.e. temporarily nearby aircraft. The auto-gain script uses the loud-messages fraction as an estimate for messages lost to excessive gain over the long term, not only the transient case.
-
Adaptive gain has a few less moving parts (i.e. no external scripts, no config changes over time) as it's built directly into dump1090 itself.