forked from iovisor/bcc
-
Notifications
You must be signed in to change notification settings - Fork 1
/
tcplife_example.txt
139 lines (110 loc) · 6.83 KB
/
tcplife_example.txt
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
Demonstrations of tcplife, the Linux BPF/bcc version.
tcplife summarizes TCP sessions that open and close while tracing. For example:
# ./tcplife
PID COMM LADDR LPORT RADDR RPORT TX_KB RX_KB MS
22597 recordProg 127.0.0.1 46644 127.0.0.1 28527 0 0 0.23
3277 redis-serv 127.0.0.1 28527 127.0.0.1 46644 0 0 0.28
22598 curl 100.66.3.172 61620 52.205.89.26 80 0 1 91.79
22604 curl 100.66.3.172 44400 52.204.43.121 80 0 1 121.38
22624 recordProg 127.0.0.1 46648 127.0.0.1 28527 0 0 0.22
3277 redis-serv 127.0.0.1 28527 127.0.0.1 46648 0 0 0.27
22647 recordProg 127.0.0.1 46650 127.0.0.1 28527 0 0 0.21
3277 redis-serv 127.0.0.1 28527 127.0.0.1 46650 0 0 0.26
[...]
This caught a program, "recordProg" making a few short-lived TCP connections
to "redis-serv", lasting about 0.25 milliseconds each connection. A couple of
"curl" sessions were also traced, connecting to port 80, and lasting 91 and 121
milliseconds.
This tool is useful for workload characterisation and flow accounting:
identifying what connections are happening, with the bytes transferred.
Process names are truncated to 10 characters. By using the wide option, -w,
the column width becomes 16 characters. The IP address columns are also wider
to fit IPv6 addresses:
# ./tcplife -w
PID COMM IP LADDR LPORT RADDR RPORT TX_KB RX_KB MS
26315 recordProgramSt 4 127.0.0.1 44188 127.0.0.1 28527 0 0 0.21
3277 redis-server 4 127.0.0.1 28527 127.0.0.1 44188 0 0 0.26
26320 ssh 6 fe80::8a3:9dff:fed5:6b19 22440 fe80::8a3:9dff:fed5:6b19 22 1 1 457.52
26321 sshd 6 fe80::8a3:9dff:fed5:6b19 22 fe80::8a3:9dff:fed5:6b19 22440 1 1 458.69
26341 recordProgramSt 4 127.0.0.1 44192 127.0.0.1 28527 0 0 0.27
3277 redis-server 4 127.0.0.1 28527 127.0.0.1 44192 0 0 0.32
In this example, I uploaded a 10 Mbyte file to the server, and then downloaded
it again, using scp:
# ./tcplife
PID COMM LADDR LPORT RADDR RPORT TX_KB RX_KB MS
7715 recordProg 127.0.0.1 50894 127.0.0.1 28527 0 0 0.25
3277 redis-serv 127.0.0.1 28527 127.0.0.1 50894 0 0 0.30
7619 sshd 100.66.3.172 22 100.127.64.230 63033 5 10255 3066.79
7770 recordProg 127.0.0.1 50896 127.0.0.1 28527 0 0 0.20
3277 redis-serv 127.0.0.1 28527 127.0.0.1 50896 0 0 0.24
7793 recordProg 127.0.0.1 50898 127.0.0.1 28527 0 0 0.23
3277 redis-serv 127.0.0.1 28527 127.0.0.1 50898 0 0 0.27
7847 recordProg 127.0.0.1 50900 127.0.0.1 28527 0 0 0.24
3277 redis-serv 127.0.0.1 28527 127.0.0.1 50900 0 0 0.29
7870 recordProg 127.0.0.1 50902 127.0.0.1 28527 0 0 0.29
3277 redis-serv 127.0.0.1 28527 127.0.0.1 50902 0 0 0.30
7798 sshd 100.66.3.172 22 100.127.64.230 64925 10265 6 2176.15
[...]
You can see the 10 Mbytes received by sshd, and then later transmitted. Looks
like receive was slower (3.07 seconds) than transmit (2.18 seconds).
Timestamps can be added with -t:
# ./tcplife -t
TIME(s) PID COMM LADDR LPORT RADDR RPORT TX_KB RX_KB MS
0.000000 5973 recordProg 127.0.0.1 47986 127.0.0.1 28527 0 0 0.25
0.000059 3277 redis-serv 127.0.0.1 28527 127.0.0.1 47986 0 0 0.29
1.022454 5996 recordProg 127.0.0.1 47988 127.0.0.1 28527 0 0 0.23
1.022513 3277 redis-serv 127.0.0.1 28527 127.0.0.1 47988 0 0 0.27
2.044868 6019 recordProg 127.0.0.1 47990 127.0.0.1 28527 0 0 0.24
2.044924 3277 redis-serv 127.0.0.1 28527 127.0.0.1 47990 0 0 0.28
3.069136 6042 recordProg 127.0.0.1 47992 127.0.0.1 28527 0 0 0.22
3.069204 3277 redis-serv 127.0.0.1 28527 127.0.0.1 47992 0 0 0.28
This shows that the recordProg process was connecting once per second.
There's also a -T for HH:MM:SS formatted times.
There's a comma separated values mode, -s. Here it is with both -t and -T
timestamps:
# ./tcplife -stT
TIME,TIME(s),PID,COMM,IP,LADDR,LPORT,RADDR,RPORT,TX_KB,RX_KB,MS
23:39:38,0.000000,7335,recordProgramSt,4,127.0.0.1,48098,127.0.0.1,28527,0,0,0.26
23:39:38,0.000064,3277,redis-server,4,127.0.0.1,28527,127.0.0.1,48098,0,0,0.32
23:39:39,1.025078,7358,recordProgramSt,4,127.0.0.1,48100,127.0.0.1,28527,0,0,0.25
23:39:39,1.025141,3277,redis-server,4,127.0.0.1,28527,127.0.0.1,48100,0,0,0.30
23:39:41,2.040949,7381,recordProgramSt,4,127.0.0.1,48102,127.0.0.1,28527,0,0,0.24
23:39:41,2.041011,3277,redis-server,4,127.0.0.1,28527,127.0.0.1,48102,0,0,0.29
23:39:42,3.067848,7404,recordProgramSt,4,127.0.0.1,48104,127.0.0.1,28527,0,0,0.30
23:39:42,3.067914,3277,redis-server,4,127.0.0.1,28527,127.0.0.1,48104,0,0,0.35
[...]
There are options for filtering on local and remote ports. Here is filtering
on local ports 22 and 80:
# ./tcplife.py -L 22,80
PID COMM LADDR LPORT RADDR RPORT TX_KB RX_KB MS
8301 sshd 100.66.3.172 22 100.127.64.230 58671 3 3 1448.52
[...]
USAGE:
# ./tcplife.py -h
usage: tcplife.py [-h] [-T] [-t] [-w] [-s] [-p PID] [-L LOCALPORT]
[-D REMOTEPORT] [-4 | -6]
Trace the lifespan of TCP sessions and summarize
optional arguments:
-h, --help show this help message and exit
-T, --time include time column on output (HH:MM:SS)
-t, --timestamp include timestamp on output (seconds)
-w, --wide wide column output (fits IPv6 addresses)
-s, --csv comma separated values output
-p PID, --pid PID trace this PID only
-L LOCALPORT, --localport LOCALPORT
comma-separated list of local ports to trace.
-D REMOTEPORT, --remoteport REMOTEPORT
comma-separated list of remote ports to trace.
-4, --ipv4 trace IPv4 family only
-6, --ipv6 trace IPv6 family only
examples:
./tcplife # trace all TCP connect()s
./tcplife -t # include time column (HH:MM:SS)
./tcplife -w # wider columns (fit IPv6)
./tcplife -stT # csv output, with times & timestamps
./tcplife -p 181 # only trace PID 181
./tcplife -L 80 # only trace local port 80
./tcplife -L 80,81 # only trace local ports 80 and 81
./tcplife -D 80 # only trace remote port 80
./tcplife -4 # only trace IPv4 family
./tcplife -6 # only trace IPv6 family