SKR Mini E3 V3 does not work with CR Touch and either of the BLtouch firmware #754

Cr0nJ0b · 2023-10-03T21:52:29Z

I'm looking for support or at least and acknowledgement that the firmware is borked.

Description

Steps to reproduce

Load firmware that reads firmware-ender3-bltouch-for-z-homing.bin:
Remover z-stop cable
init eeprom
rename and load firmware onto the board
verify that the menu for BLtouch exists -- it does
Home all

Expected behavior
All axes should home correctly to zero. Specifically, the x and y should home, then the head should lift 11mm or so and move to the center of the bed. The probe should extend and the z axis should lower until the probe touches the bed and activates the sensor, verifying Z home.

Actual behavior
X and y home, but then at whatever height the head is at it will lift and center (height will be 11mm+ original height). the probe will extend from the sensor. z axis will descend 11mm or so and the sensor will pull in, drop out again and pull in. At this point the menu will read STOPPPED.

Additional Information

I'm using the Stock firmware provided by BTT. I did not roll this firmware. If I had to guess there is either an issue with the board processor and wiring between the CR touch and the BL touch.

Staticshift15 · 2023-10-08T19:51:49Z

My Ender 5 pro is doing exactly the same thing

aero-gro · 2023-10-10T19:39:10Z

Same problem here, updating an Ender 3.

kirgy · 2023-10-16T21:18:26Z

Same issue, unable to operate ender 3 pro with upgrade to SKR mini e3 3.0.

Stoutscientist · 2023-10-24T22:35:53Z

Same, for a $50 board they really don't know how to fix their bugs, I have seen reports of this for ~3 years. The solutions I have seen require cutting wires and this is advertised as a drop in replacement.

Stoutscientist · 2023-10-24T22:41:23Z

Also, the firmware hasn't been updated in over a year...

Davmaker · 2023-11-15T03:16:02Z

YO TAMBIEN E TENIDO PROBLEMAS CON LA MINI E3 V3-0 Y EL BLTOUCH , ADEMAS DE QUE CPMPRE UNA PANTALLA TFT35 3.0 , SUPUESTAMENTE ES COMPATIBLE CON CREALITY ENDER 5 PLUS. DECEPCION AL VER QUE EL MODO TACTIL NO CONECTA CON LA IMPRESORA , UNICAMENTE PUEDO USAR EL MODO MARLIN, SI ALGUIEN PUEDE AYUDAR LO AGRADECERÉ MUCHISIMO!!! GRACIAS

kirgy · 2023-11-15T10:38:38Z

To solve this, I learnt how to compile the firmware by following a number of youtube videos around "marlin ender 3 firmware compilation"

Out of the back of that I created this repo which does that firmware compiling for my specific scenario. All I can suggest for others is you follow these tutorials to do it yourself - given the lack of support from bigtreetech.

https://github.com/kirgy/marlin-firmware-ender-3-pro-skr-mini-e3-crtouch

wildseyed · 2023-12-24T01:34:15Z

To solve this, I learnt how to compile the firmware by following a number of youtube videos around "marlin ender 3 firmware compilation"

Out of the back of that I created this repo which does that firmware compiling for my specific scenario. All I can suggest for others is you follow these tutorials to do it yourself - given the lack of support from bigtreetech.

https://github.com/kirgy/marlin-firmware-ender-3-pro-skr-mini-e3-crtouch

Has anyone had luck recently trying to compile? Seems like Marlin AutoBuild is broken, asuming the source above did compile at some point. It's been three weeks since I put the new board in my ender. Nothing but regrets ATM.

Stoutscientist · 2023-12-29T21:36:12Z

To solve this, I learnt how to compile the firmware by following a number of youtube videos around "marlin ender 3 firmware compilation"
Out of the back of that I created this repo which does that firmware compiling for my specific scenario. All I can suggest for others is you follow these tutorials to do it yourself - given the lack of support from bigtreetech.
https://github.com/kirgy/marlin-firmware-ender-3-pro-skr-mini-e3-crtouch

Has anyone had luck recently trying to compile? Seems like Marlin AutoBuild is broken, asuming the source above did compile at some point. It's been three weeks since I put the new board in my ender. Nothing but regrets ATM.

I actually did get it to work! Here's the file:

https://download1530.mediafire.com/kp3u9ry0anngT8UOndJEzNY_7YSnGBhrM4g3OZjPONxrN9pyMKAyOmX7NFpCusCKw4yJ4k8G8CmBP93ax5MWtLgourZiMP1pcIRoqVjRyEl0IkMFk9dVpJxwq5kupgoYNziX0YZ5HOyXMSW08nNlv0rjDEKuuV0G22_VCmKMRQ/h0nfbk4k4iaiki5/firmware.bin

The reason it wasn't compiling was because a library was updated since that guy posted and so when it tried to download it, it was the wrong version so I just back dated it

wildseyed · 2023-12-30T03:07:01Z

Thanks for the file! That has me back up and running with the BL.

…

On Fri, Dec 29, 2023 at 1:36 PM Stoutscientist ***@***.***> wrote: To solve this, I learnt how to compile the firmware by following a number of youtube videos around "marlin ender 3 firmware compilation" Out of the back of that I created this repo which does that firmware compiling for my specific scenario. All I can suggest for others is you follow these tutorials to do it yourself - given the lack of support from bigtreetech. https://github.com/kirgy/marlin-firmware-ender-3-pro-skr-mini-e3-crtouch Has anyone had luck recently trying to compile? Seems like Marlin AutoBuild is broken, asuming the source above did compile at some point. It's been three weeks since I put the new board in my ender. Nothing but regrets ATM. I actually did get it to work! Here's the file: https://download1530.mediafire.com/kp3u9ry0anngT8UOndJEzNY_7YSnGBhrM4g3OZjPONxrN9pyMKAyOmX7NFpCusCKw4yJ4k8G8CmBP93ax5MWtLgourZiMP1pcIRoqVjRyEl0IkMFk9dVpJxwq5kupgoYNziX0YZ5HOyXMSW08nNlv0rjDEKuuV0G22_VCmKMRQ/h0nfbk4k4iaiki5/firmware.bin — Reply to this email directly, view it on GitHub <#754 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AAFMKGQUCSXIY2QQLDA2MADYL4ZVPAVCNFSM6AAAAAA5RULU46VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQNZSGM2DSMZTHA> . You are receiving this because you commented.Message ID: ***@***.***>

Stoutscientist · 2023-12-30T03:30:35Z

Thanks for the file! That has me back up and running with the BL.
…
On Fri, Dec 29, 2023 at 1:36 PM Stoutscientist @.> wrote: To solve this, I learnt how to compile the firmware by following a number of youtube videos around "marlin ender 3 firmware compilation" Out of the back of that I created this repo which does that firmware compiling for my specific scenario. All I can suggest for others is you follow these tutorials to do it yourself - given the lack of support from bigtreetech. https://github.com/kirgy/marlin-firmware-ender-3-pro-skr-mini-e3-crtouch Has anyone had luck recently trying to compile? Seems like Marlin AutoBuild is broken, asuming the source above did compile at some point. It's been three weeks since I put the new board in my ender. Nothing but regrets ATM. I actually did get it to work! Here's the file: https://download1530.mediafire.com/kp3u9ry0anngT8UOndJEzNY_7YSnGBhrM4g3OZjPONxrN9pyMKAyOmX7NFpCusCKw4yJ4k8G8CmBP93ax5MWtLgourZiMP1pcIRoqVjRyEl0IkMFk9dVpJxwq5kupgoYNziX0YZ5HOyXMSW08nNlv0rjDEKuuV0G22_VCmKMRQ/h0nfbk4k4iaiki5/firmware.bin — Reply to this email directly, view it on GitHub <#754 (comment)>, or unsubscribe https://github.com/notifications/unsubscribe-auth/AAFMKGQUCSXIY2QQLDA2MADYL4ZVPAVCNFSM6AAAAAA5RULU46VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTQNZSGM2DSMZTHA . You are receiving this because you commented.Message ID: @.>

Awesome! I've also been having this issue so I finally decided to put some research into it and ended up finding the fix today.

MpSv8 · 2024-01-19T16:16:07Z

To solve this, I learnt how to compile the firmware by following a number of youtube videos around "marlin ender 3 firmware compilation"
Out of the back of that I created this repo which does that firmware compiling for my specific scenario. All I can suggest for others is you follow these tutorials to do it yourself - given the lack of support from bigtreetech.
https://github.com/kirgy/marlin-firmware-ender-3-pro-skr-mini-e3-crtouch

Has anyone had luck recently trying to compile? Seems like Marlin AutoBuild is broken, asuming the source above did compile at some point. It's been three weeks since I put the new board in my ender. Nothing but regrets ATM.

I actually did get it to work! Here's the file:

https://download1530.mediafire.com/kp3u9ry0anngT8UOndJEzNY_7YSnGBhrM4g3OZjPONxrN9pyMKAyOmX7NFpCusCKw4yJ4k8G8CmBP93ax5MWtLgourZiMP1pcIRoqVjRyEl0IkMFk9dVpJxwq5kupgoYNziX0YZ5HOyXMSW08nNlv0rjDEKuuV0G22_VCmKMRQ/h0nfbk4k4iaiki5/firmware.bin

The reason it wasn't compiling was because a library was updated since that guy posted and so when it tried to download it, it was the wrong version so I just back dated it

hey, @Stoutscientist are you able to make such a file for Ender 3 (no pro version)?

Stoutscientist · 2024-01-19T16:42:37Z

To solve this, I learnt how to compile the firmware by following a number of youtube videos around "marlin ender 3 firmware compilation"
Out of the back of that I created this repo which does that firmware compiling for my specific scenario. All I can suggest for others is you follow these tutorials to do it yourself - given the lack of support from bigtreetech.
https://github.com/kirgy/marlin-firmware-ender-3-pro-skr-mini-e3-crtouch

Has anyone had luck recently trying to compile? Seems like Marlin AutoBuild is broken, asuming the source above did compile at some point. It's been three weeks since I put the new board in my ender. Nothing but regrets ATM.

I actually did get it to work! Here's the file:

https://download1530.mediafire.com/kp3u9ry0anngT8UOndJEzNY_7YSnGBhrM4g3OZjPONxrN9pyMKAyOmX7NFpCusCKw4yJ4k8G8CmBP93ax5MWtLgourZiMP1pcIRoqVjRyEl0IkMFk9dVpJxwq5kupgoYNziX0YZ5HOyXMSW08nNlv0rjDEKuuV0G22_VCmKMRQ/h0nfbk4k4iaiki5/firmware.bin

The reason it wasn't compiling was because a library was updated since that guy posted and so when it tried to download it, it was the wrong version so I just back dated it

hey, @Stoutscientist are you able to make such a file for Ender 3 (no pro version)?

I can try but tbh I have no idea what I'm doing lol

DanKreck · 2024-01-28T16:45:10Z

I flashed that firmware, and when Level Bed, the nozzle goes passed the right side of the bed. Is this expected?

Stoutscientist · 2024-01-29T00:03:17Z

What's your setup?

DanKreck · 2024-01-29T00:24:13Z

What's your setup?

I have an Ender 3 Pro, with a SKR Mini E3 V3 board, running the firmware posted above. Fixed my Z axis issues related to the CR touch, so thats good. Just noticed that while leveling the bed the nozzle goes far right. I was wondering if it was intentional, to get the CR touch probe closer to the right side, but its not much.... maybe 1/4 inch.

Stoutscientist · 2024-02-01T04:16:46Z

What's your setup?

I have an Ender 3 Pro, with a SKR Mini E3 V3 board, running the firmware posted above. Fixed my Z axis issues related to the CR touch, so thats good. Just noticed that while leveling the bed the nozzle goes far right. I was wondering if it was intentional, to get the CR touch probe closer to the right side, but its not much.... maybe 1/4 inch.

If you attach a photo I can double check but mine does something similar and prints fine so I think it's normal

Stoutscientist · 2024-02-01T04:18:23Z

To solve this, I learnt how to compile the firmware by following a number of youtube videos around "marlin ender 3 firmware compilation"
Out of the back of that I created this repo which does that firmware compiling for my specific scenario. All I can suggest for others is you follow these tutorials to do it yourself - given the lack of support from bigtreetech.
https://github.com/kirgy/marlin-firmware-ender-3-pro-skr-mini-e3-crtouch

Has anyone had luck recently trying to compile? Seems like Marlin AutoBuild is broken, asuming the source above did compile at some point. It's been three weeks since I put the new board in my ender. Nothing but regrets ATM.

I actually did get it to work! Here's the file:
https://download1530.mediafire.com/kp3u9ry0anngT8UOndJEzNY_7YSnGBhrM4g3OZjPONxrN9pyMKAyOmX7NFpCusCKw4yJ4k8G8CmBP93ax5MWtLgourZiMP1pcIRoqVjRyEl0IkMFk9dVpJxwq5kupgoYNziX0YZ5HOyXMSW08nNlv0rjDEKuuV0G22_VCmKMRQ/h0nfbk4k4iaiki5/firmware.bin
The reason it wasn't compiling was because a library was updated since that guy posted and so when it tried to download it, it was the wrong version so I just back dated it

hey, @Stoutscientist are you able to make such a file for Ender 3 (no pro version)?

I actually just read that the Ender 3 Pro and non pro use the same firmware so it should work for you

CelticNickC · 2024-02-08T01:16:23Z

I performed the flash on ender 3, but it runs the nozzle into the plate with this firmware

Chilson3D · 2024-02-08T02:07:46Z

mine works, ill share a snip of my .cfg I do remember reading a post that the "pin out" needs to be changed as follows:
Updated BL Touch PIN for CR touch #718
@@ -10,7 +10,7 @@
Line 10 # See docs/Config_Reference.md for a description of parameters.
Line 11
Line 12 [bltouch]
Line 13 sensor_pin: PC14 #(wrong code)
Line 13 sensor_pin: ^PC14 #(correct code)
Line 14 control_pin: PA1
Line 15 x_offset: -40
Line 16 y_offset: -10

My setting:
[bltouch]
sensor_pin: ^PC14
control_pin: PA1
x_offset: -45.5
y_offset: -9
#z_offset: 3.0
#speed:

Chilson3D · 2024-02-08T02:09:08Z

mine works, ill share a snip of my .cfg I do remember reading a post that the "pin out" needs to be changed as follows:
Updated BL Touch PIN for CR touch #718
@@ -10,7 +10,7 @@
Line 10 # See docs/Config_Reference.md for a description of parameters.
Line 11
Line 12 [bltouch]
Line 13 sensor_pin: PC14 #(wrong code)
Line 13 sensor_pin: ^PC14 #(correct code)
Line 14 control_pin: PA1
Line 15 x_offset: -40
Line 16 y_offset: -10

My setting:
[bltouch]
sensor_pin: ^PC14
control_pin: PA1
x_offset: -45.5
y_offset: -9
#z_offset: 3.0
#speed:

CelticNickC · 2024-02-08T06:22:11Z

mine works, ill share a snip of my .cfg I do remember reading a post that the "pin out" needs to be changed as follows:

Updated BL Touch PIN for CR touch #718
  	@@ -10,7 +10,7 @@
Line 10 # See docs/Config_Reference.md for a description of parameters.

Line 11

Line 12 [bltouch]

Line 13 sensor_pin: PC14 #(wrong code)

Line 13 sensor_pin: ^PC14 #(correct code)

Line 14 control_pin: PA1

Line 15 x_offset: -40

Line 16 y_offset: -10

My setting:

[bltouch]

sensor_pin: ^PC14

control_pin: PA1

x_offset: -45.5

y_offset: -9

#z_offset: 3.0

#speed:

So I went through and attempted to edit coding while following videos. Nearly all of the codes changed were in far different spots due to the updating on the file being used compared to the video. I’m still coming back with the same issue even after seeing changes validated from the edit. I had to pull the bin file from vsc and drag it onto my sd card. I’m using an old MacBook to try to program these codes, and the file just wasn’t showing up anywhere even if I had zero errors.

The error showing up after the bltouch touches down says “error:
!! STOP called because of BLTouch error -restart with m999”

Any actions to take for this or ideas of code to tweak? I was not able to locate in the coding where your recommendations for pins would be

topybear · 2024-02-08T12:30:43Z

Any actions to take for this or ideas of code to tweak? I was not able to locate in the coding where your recommendations for pins would be

Not in code. Printer.cfg file.

CelticNickC · 2024-02-08T19:01:07Z

Any actions to take for this or ideas of code to tweak? I was not able to locate in the coding where your recommendations for pins would be

Not in code. Printer.cfg file.

Would I need to add this file to the build to be able to adjust? Or where would I find the printer.cfg file?

config/Ender-3 Pro/SKR-Mini-E3-V3.0/printer.cfg

topybear · 2024-02-08T21:55:52Z

This is Klipper config file.

CelticNickC · 2024-02-09T01:28:41Z

This is Klipper config file.

Would it work the same as for marlin?

DINOS-DEAD · 2024-02-15T04:04:05Z

I got fet up and just went to TH3Dstudio payed the five bucks and finished the config.h file as instructed and add my features, compiled and now up and running less than an 30 minutes

Seelenkind · 2024-07-24T14:46:02Z

try this, my new updated firmware with actual Marlin
#776

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

SKR Mini E3 V3 does not work with CR Touch and either of the BLtouch firmware #754

SKR Mini E3 V3 does not work with CR Touch and either of the BLtouch firmware #754

Cr0nJ0b commented Oct 3, 2023

Staticshift15 commented Oct 8, 2023

aero-gro commented Oct 10, 2023

kirgy commented Oct 16, 2023

Stoutscientist commented Oct 24, 2023 •

edited

Loading

Stoutscientist commented Oct 24, 2023

Davmaker commented Nov 15, 2023

kirgy commented Nov 15, 2023

wildseyed commented Dec 24, 2023

Stoutscientist commented Dec 29, 2023 •

edited

Loading

wildseyed commented Dec 30, 2023 via email

Stoutscientist commented Dec 30, 2023

MpSv8 commented Jan 19, 2024

Stoutscientist commented Jan 19, 2024

DanKreck commented Jan 28, 2024

Stoutscientist commented Jan 29, 2024

DanKreck commented Jan 29, 2024

Stoutscientist commented Feb 1, 2024

Stoutscientist commented Feb 1, 2024

CelticNickC commented Feb 8, 2024

Chilson3D commented Feb 8, 2024 •

edited

Loading

Chilson3D commented Feb 8, 2024

CelticNickC commented Feb 8, 2024

topybear commented Feb 8, 2024

CelticNickC commented Feb 8, 2024

topybear commented Feb 8, 2024

CelticNickC commented Feb 9, 2024

DINOS-DEAD commented Feb 15, 2024

Seelenkind commented Jul 24, 2024

SKR Mini E3 V3 does not work with CR Touch and either of the BLtouch firmware #754

SKR Mini E3 V3 does not work with CR Touch and either of the BLtouch firmware #754

Comments

Cr0nJ0b commented Oct 3, 2023

Description

Steps to reproduce

Additional Information

Staticshift15 commented Oct 8, 2023

aero-gro commented Oct 10, 2023

kirgy commented Oct 16, 2023

Stoutscientist commented Oct 24, 2023 • edited Loading

Stoutscientist commented Oct 24, 2023

Davmaker commented Nov 15, 2023

kirgy commented Nov 15, 2023

wildseyed commented Dec 24, 2023

Stoutscientist commented Dec 29, 2023 • edited Loading

wildseyed commented Dec 30, 2023 via email

Stoutscientist commented Dec 30, 2023

MpSv8 commented Jan 19, 2024

Stoutscientist commented Jan 19, 2024

DanKreck commented Jan 28, 2024

Stoutscientist commented Jan 29, 2024

DanKreck commented Jan 29, 2024

Stoutscientist commented Feb 1, 2024

Stoutscientist commented Feb 1, 2024

CelticNickC commented Feb 8, 2024

Chilson3D commented Feb 8, 2024 • edited Loading

Chilson3D commented Feb 8, 2024

CelticNickC commented Feb 8, 2024

topybear commented Feb 8, 2024

CelticNickC commented Feb 8, 2024

topybear commented Feb 8, 2024

CelticNickC commented Feb 9, 2024

DINOS-DEAD commented Feb 15, 2024

Seelenkind commented Jul 24, 2024

Stoutscientist commented Oct 24, 2023 •

edited

Loading

Stoutscientist commented Dec 29, 2023 •

edited

Loading

Chilson3D commented Feb 8, 2024 •

edited

Loading