laser doen(t worl #1188
Replies: 9 comments
-
Well, it is normal for your cooler fan to make noise. Other than that, the homing cycle clicks your end switches 2 times (by default), the first one faster, the second one a bit slower to properly get it's position. No other noise should come from your machine as far as I know.
I don't quite get that
What is the GCode (program) you try to send to your machine? What is your |
Beta Was this translation helpful? Give feedback.
-
Hello , thank you for your reply . Can I send you the video for the Noise? I just start with this machine , and so , I don't understand : What is the GCode (program) you try to send to your machine? What is your laser test command? Best regards. Jean |
Beta Was this translation helpful? Give feedback.
-
I use the ortur master 2 with the software lasergrlb |
Beta Was this translation helpful? Give feedback.
-
Beta Was this translation helpful? Give feedback.
-
On the video you've sent me it sounded like your stepper motor was running. The video was too short, so I'm not 100% sure. One thing I'm certain about, it seems a hardware issue, so I advise you contact Ortur support here or at their Facebook page |
Beta Was this translation helpful? Give feedback.
-
Hi,
thank you again for your replay; I fix my noise problem ( wrong connection )but now , there is no noise , and the home process is working properly , the program is runnig properly , but since, there is not lazer working, only the fan is working :-(
I ll send the video with wetranfer , because to big size....
I dont now why?
BR
Le mardi 8 décembre 2020 à 12:34:48 UTC+1, Alex <[email protected]> a écrit :
On the video you've sent me it sounded like your stepper motor was running. The video was too short, so I'm not 100% sure. One thing I'm certain about, it seems a hardware issue, so I advise you contact Ortur support here or at their Facebook page
—
You are receiving this because you authored the thread.
Reply to this email directly, view it on GitHub, or unsubscribe.
|
Beta Was this translation helpful? Give feedback.
-
Hello , ths is 2 video I made to show you my issue :
https://www.youtube.com/watch?v=m4jkpxNa5kU
https://www.youtube.com/watch?v=8r1VA3PoQvs
Have a nive evening.cdllt
Le mardi 8 décembre 2020 à 21:48:28 UTC+1, Jean Prevot <[email protected]> a écrit :
Hi,
thank you again for your replay; I fix my noise problem ( wrong connection )but now , there is no noise , and the home process is working properly , the program is runnig properly , but since, there is not lazer working, only the fan is working :-(
I ll send the video with wetranfer , because to big size....
I dont now why?
BR
Le mardi 8 décembre 2020 à 12:34:48 UTC+1, Alex <[email protected]> a écrit :
On the video you've sent me it sounded like your stepper motor was running. The video was too short, so I'm not 100% sure. One thing I'm certain about, it seems a hardware issue, so I advise you contact Ortur support here or at their Facebook page
—
You are receiving this because you authored the thread.
Reply to this email directly, view it on GitHub, or unsubscribe.
|
Beta Was this translation helpful? Give feedback.
-
Just for testing, if you type |
Beta Was this translation helpful? Give feedback.
-
Hello , i will check it , I dont know this evenin g i ll try to check you adwise . BR
Le mercredi 9 décembre 2020 à 20:33:41 UTC+1, Alex <[email protected]> a écrit :
Just for testing, if you type G1F1M4S1 and then G1F1M4S1000, which one produces brighter laser light? It might be your laser driver needs inverted TTL signal. (As your GCode seems to send S1000 on the second video)
—
You are receiving this because you authored the thread.
Reply to this email directly, view it on GitHub, or unsubscribe.
|
Beta Was this translation helpful? Give feedback.
-
hello ,
Is it normal for the machine to make this noise during the
end of the homing cycle?
and too, the probrem is take a very long time , the buffer stay running and can't start.
too , when is start,
the laser test command works but the lazer does not work anymore during the program phases.
is this problem due to the fact that my computer has 4 GB RAM?
Thank you for your help.
Beta Was this translation helpful? Give feedback.
All reactions