wide_alu.hjson

{
    name: "wide_alu",
    clock_primary: "clk_i",
    reset_primary: "rst_ni",
    bus_interfaces: [{ protocol: "reg_iface", direction: "device"}],
    
    regwidth: "32",
    registers: [
        { multireg:
          { name: "OP_A",
            desc: "Subword of Operand A.",
            count: "8",
            cname: "OP_A",
            swaccess: "wo",
            fields: [
                { bits: "31:0"
                }
            ],
          }
        },
        { multireg:
          { name: "OP_B",
            desc: "Subword of Operand B.",
            count: "8",
            cname: "OP_B",
            swaccess: "wo",
            fields: [
                { bits: "31:0"
                }
            ],
          }
        },
        { multireg:
          { name: "RESULT",
            desc: "Subword of results.",
            count: "16",
            cname: "RESULT",
            swaccess: "ro",
            hwaccess: "hwo",
            hwext: "true",
            fields: [
                { bits: "31:0"
                }
            ],
          }
        },
        { name: "CTRL1",
          desc: "Controls clear and trigger signal of the deaccelerator.",
          swaccess: "wo",
          hwaccess: "hro",
          hwext: "true",
          hwqe: "true",
          fields: [
              { bits: "0", name: "TRIGGER",
                desc: "Trigger operation on rising edge."
              }
              { bits: "1", name: "CLEAR_ERR",
                desc: "Clear a pending ERROR in the deaccelerator."
              }
          ]
        },
        { name: "CTRL2",
          desc: "Configures the operation and its delay within the deaccelerator.",
          swaccess: "rw",
          hwaccess: "hrw",
          hwext: "true",
          hwqe: "true",
          fields: [
              { bits: "2:0", name: "OPSEL",
                desc: "Select the operation to perform.",
                enum: [
                    { value: "0", name: "ADD", desc: "Perform add operation." },
                    { value: "1", name: "SUB", desc: "Perform sub operation." },
                    { value: "2", name: "MUL", desc: "Perform mul operation." },
                    { value: "3", name: "XOR", desc: "Perform xor operation." },
                    { value: "4", name: "AND", desc: "Perform and operation." },
                    { value: "5", name: "OR", desc: "Perform or operation." },
                ]
              }
              { bits: "23:16", name: "DELAY",
                desc: "Configures the number of cycles the deaccelerator requires to finishe the operation. "
              }
          ]
        },
        { name: "STATUS",
          desc: "Contains the current status of the Deaccelerator.",
          swaccess: "ro",
          hwaccess: "hwo",
          hwext: "true",
          fields: [
              { bits: "1:0", name: "CODE",
                desc: "The current status code of the accelerator.",
                enum: [
                    { value: "0", name: "IDLE", desc: "Accelerator is idle, results are avaialble for read."},
                    { value: "1", name: "PENDING", desc: "Pending operation. Chaning configuration while pending results in an error."},
                    { value: "2", name: "ERROR_WRITE", desc: "A configuration change was attempted during pending operation."},
                    { value: "3", name: "ERROR_OPCODE", desc: "The accelerator was supplied with an unknown opcode."}
                ]}
          ]
        }
    ],
}